Technical Data
Lubricating system
Pump, type ............................................................................. Circulation pump for distribution of oil to all lubri-
cation points
Oil quality................................................................................ Engine oil
Viscosity ................................................................................. Multigrade SAE 10W-30 aft. 10W-40
Oil quality, approx ................................................................... 2.6 liters (US Qts. 2 3/4)
Oil quantity, 1" extension, approx. .......................................... 2.6 liters (US Qts. 2 3/4)
Oil quantity, 4" extension, approx. .......................................... 2.8 liters (US Qts. 3.0)
Oil capacity between min. and max. marks, approx. ............... 0.15 liters (US Qts. 0.16)
Power Trim,
1)
oil quality .......................................................................... ATF oil
2)
oil quantity ........................................................................ 1.0 liters (1.1 US Qts.)
Tightening torques
Nm
Lb. ft.
Upper nut vertical shaft (upper gear) .......................................
Tightening universal joint.........................................................
Assembly double bearing box – gear housing .........................
Assembly of top cover to upper gear housing .........................
Lower nut vertical shaft ...........................................................
Bearing box with propeller shaft in gear housing ......................
Intermediate housing – lower gear housing ..............................
Oil drain plug ...........................................................................
Oil filler plug ............................................................................
Intermediate housing – upper gear housing .............................
Steering helmet ‘attachment bolt’, Earlier model .....................
Steering helmet ‘attachment bolt’, Later model........................
125
92
125
35
3)
92
26
11
3)
15
160
40
118
30
38
10
35
38
4)
28
4)
7.5
25
28
50–60
35
36–44
25
Pre-stressing
Input gear in double bearing box, 280–290 .............................. 5–10 N (1.102–2.205 lb.)
Input gear in double bearing box, run-in gears, 280–290 .......... 2.5–5 N (0.55–1.102 lb.)
Input gear in double bearing box, 290A ................................... 10–15 N (2.20–3.30 lb.)
Input gear in double bearing box, run-in gears, 290A ............... 7.5–10 N (1.65–2.2 lb.)
1)
2)
Alt. Volvo Penta oil for petrol or diesel engines. See Owners Manual.
Early production drives were filled with engine oil and have that recommendation in the Owner’s Manual. Late production drives have ATF
oil filled. We recommend the use of ATF oil. Observe strict cleanliness so that dirt is not drawn in by the oil.
NOTE! Never mix ATF oil with engine oil, as this will cause foaming and possible pump failure.
3)
4)
As from PZ number 2721099 the following tightening torque should be applied: 75 Nm (55.2 lb. ft.)
The tightening torque for the three thinner bolts (two long and one short) is 15 Nm (10 lb. ft.). This applies to all drives.
169
| Categories | Volvo Penta Manuals |
|---|---|
| Tags | Volvo Penta 280, Volvo Penta 280-DP, Volvo Penta 285, Volvo Penta 290, Volvo Penta 290-DP, Volvo Penta DP-A, Volvo Penta DP-B, Volvo Penta DP-C, Volvo Penta SP-A, Volvo Penta SP-C |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(9 votes, average: 4.22 out of 5)
Marine readers have rated Volvo Penta 280 285 290 DP SP A B C Workshop Manual 4.2 out of 5.0 based on 9 product reviews. Problem Winther noise when turne
not pulling water so hope I find the info
Kinda a premature review, at this point I am asked to review the manual before ever seeing it?
Great step by step information.
thank you
needed it bad
ok