Repair instructions
Installing a ‘short hub’ type of
propeller (B)
Oil filling
1.
2.
Install the oil drain plug with a new O-ring.
1.
Grease the propeller shaft with a thin layer of
grease.
Tilt the sterndrive to the full up position. Remove
the fill plug and fill with approx. 2.2 liters of gear oil.
See Technical Data. Install the fill plug with a new
gasket.
2.
Install the fishing line deflector (5, figure on previ-
ouspage).
3.
4.
Install the propeller.
Tighten the fill plug to 35 Nm (26 lb.ft.).
Alternative1:(Threadedholeinthepropeller
shaft center). Insert the plastic washer (3).
Lower the sterndrive and check the oil level with the
dipstick. If necessary, Top off the sterdrive with oil
through the dip stick hole.
Alternative 2:(Nothreadedholeinthepropeller
shaft center). Insert the folding washer (4).
3.
Install the shift mechanism cover.
5.
6.
7.
Install the spacer ring, (2).
Install and tighten the propeller cone (1).
Alternative 1: Install and tighten the center
screw.
Alternative 2: Fold the washer (4) against the
spacer ring (2).
Propeller installation
NOTE! The sterndrive model 280B, ratio 1.61:1, is
different from model 280D and model 270, ratio
2.15:1.
The difference is to be found in the fact that
the propellers have ‘long hubs’ and ‘short hubs’ re-
spectively. See the picture.
NOTE! Short hub propellers (folding washer and cone)
will be replaced by long hub propellers (plastic washer,
cone, center bolt). When installing long hub propellers
on older sterndrives, the propeller shaft must be drilled
and tapped for use of cone with center bolt.
Use drill jigg 885149 to drill the propeller shaft elimi-
nating the need to remove the shaft from the drive unit
as follows:
On propellers of earlier manufacture the propeller cone
is locked by a folding washer and on propellers of later
manufacture the cone is locked by a locking screw
through the center of the cone.
1.
2.
Install drill jigg on propeller shaft.
Drill a 6.5 mm (0.255”) hole to a depth of 20 mm
(0.787”).
ougly.
Use cutting oil to cool shaft. Clean thor-
Installing a ‘long hub’ type of
propeller (A)
3.
4.
Usa a 5/16”-18 UNC taps to thread shaft. Clean
thorougly.
1.
Grease the propeller shaft with a thin layer of
grease.
Install propeller, plastic washer, cone and center
bolt. Torque: cone = 110 Nm (81 ft.lb.), bolt =
2.
3.
4.
5.
6.
Install the fishing line deflector (5).
Install the propeller.
22
Nm (16 ft.lb.).
Install the plastic washer.
Install the propeller cone (1) and tighten it.
Install and tighten the center screw.
128
| Categories | Volvo Penta Manuals |
|---|---|
| Tags | Volvo Penta 280, Volvo Penta 280-DP, Volvo Penta 285, Volvo Penta 290, Volvo Penta 290-DP, Volvo Penta DP-A, Volvo Penta DP-B, Volvo Penta DP-C, Volvo Penta SP-A, Volvo Penta SP-C |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(9 votes, average: 4.22 out of 5)
Marine readers have rated Volvo Penta 280 285 290 DP SP A B C Workshop Manual 4.2 out of 5.0 based on 9 product reviews. Problem Winther noise when turne
not pulling water so hope I find the info
Kinda a premature review, at this point I am asked to review the manual before ever seeing it?
Great step by step information.
thank you
needed it bad
ok