be wired directly to the fuse block below the dash or
may be wired to a circuit breaker in the AC/DC cabin
panel. For additional information on adding accesso-
ries, refer to Section H-5B.
LTS switch towards the NAV position activates the
bow lights, the all-around light and the instrument
lights on the dash. Move the switch to the ANC
position to activate the all-around light. The center
switch posi tion is “OFF”.
Volt DC Receptacle - Permits the use of additional
appropriate adaptor, the equipment draws power from
the boat’s batteries.
2 volt equipment such as a cell phone. Using the
Arch Lights - The ARCH LIGHTS switch is used to
activate the radar arch lights.
Platform Lights - The PLATFORM LIGHTS switch is
used to activate the lights for the swim platform.
Aft Bilge Pump - The BILGE PUMP switch is used
to manually activate the bilge pump in the engine
compartment. The bilge pump is used to remove
water from the bilge (bottom of the hull) area of the
boat by pumping that water overboard. The aft bilge
pump is equipped with an automatic bilge switch and
will operate whenever bilge water rises to a level that
will cause the ﬂoat to move upward.
Engine Lights - The ENGINE LIGHTS switch is used
to activate the engine lights in the engine compart-
Trim Tabs - The boat is equipped with electric-
hydraulic trim tabs, the trim tabs are controlled by the
TRIM TAB switches. Refer to Section E-8 - Trim Tabs
for more information.
This automatic bilge pump is active even if the battery
selector switch is in the “OFF” position or if no battery
selector switch is installed. The automatic bilge pump
circuitry is connected directly to the batteries. When
leaving your boat unattended for an extended period,
check the charge on the battery(s) periodically. Also
check the water level in the bilge and make sure the
ﬂoat switch is functional.
Windlass - The WINDLASS switch activates the
windlass. A circuit breaker is located on the battery
switch panel. Refer to the Section M-12 in this manual
and the manufacturer’s literature for additional
Engine Hatch - The ENGINE HATCH switch is used
to raise and lower the engine lid by activating a linear
screw jack. Pressing the upper portion of the switch
marked “UP” allows the engine lid to be raised.
Pressing the lower portion of switch marked “DOWN”
If the automatic bilge pump must be disabled, discon-
nect the wiring plug near the bilge pump.
Blower - The BLOWER switch is used to activate the
bilge blower. Pressing the switch to the “ON” position, lowers the engine lid.
activates the electric bilge blowers, changing the air in
the engine compartment that may contain gas vapors.
Wiper - The WIPER SELECT switch activates the
desired windshield wiper(s). The wiper(s) will self
Gasoline vapors can explode resulting in injury
or death. Before starting the engine, check
engine compartment bilge for gasoline or
vapors. Operate blower for four minutes, and
verify blower operation. ALWAYS run the
blower when the vessel is operating below
B. Installation of Additional 12 Volt Equipment
Accessories may be added to the boat by wiring
directly to the cabin panel. Non-factory installed
volt accessory equipment can be connected to
the “ACC” switch on the dash.
Cockpit Lights - The COCKPIT LTS switch is used to
activate the cockpit (courtesy) lights. An additional
cockpit light switch is typically located on the cabin
light switch panel.
Horn - To sound the horn, press the HORN switch.
Navigation & Anchor Lights - Moving the NAV/ANC
Electrical Systems - Section H
Owner’s Manual Page 69
|Categories||Four Winns Manuals, Four Winns V-Series Manuals|
|Tags||Four Winns V335|
|Document Type||Owner's Manual|
|Product Brand||Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx|
|Document File Type|
|Wikipedia's Page||Outboard Marine Corporation|
(0 votes, average: 0 out of 5)