™
manual included in the owner’s packet. DO NOT
USEMULTIGRADEOIL. Powersteering and power
trim use automatic transmission fluid. Check the
fluid levels in the vertical drive units or transmission
as often as practical.
•
•
Turn key switch to the START position.
Immediately move the control handle to the idle po-
sition when the engine starts.
NOTICE
THE FOLLOWING
IF THE LOWEST
Failure to move the control handle to the idle
position immediately when engine starts will al-
low engine to “over-rev” and engine damage
could result. “Over-revving” engine after off-
season storage could also damage the water
pump impeller. When starting engine for the
first time after off-season storage, always
idle engine for one minute to allow the wa-
ter pump to prime.
SAE VISCOSITY
ANTICIPATED
TEMPERATURE IS*
RECOMMENDED
OILS ARE
3
2
O
F (0
o
C) and above
F (0 C)
O
SAE 30
SAE 20W-20
SAE 10W
0
O
F (-18 C) to 32
O
O
Below 0 F (-18 C)
O O
*
Temperature range you expect to operate.
Note: Use only single viscosity oils.
3.
As soon as engine starts:
Table 1: SAE Viscosity Chart
a.
b.
Release key to the ON or RUN position.
3.
4.
Start and operate the bilge blower system for at least
four (4) minutes before start-up.
Move control handle to the fast idle position to
warm up engine. DO NOT exceed 1000 RPM.
Lower the vertical outdrive units (on applicable mod-
els) making sure the water intakes are under the
water.
NOTICE
Cold engine starting procedures are different for
EFI engines. Priming is not necessary. Refer
to the engine owner’s manual for additional
information.
B. Cold Engine Start (Carbureted Engines)
1.
The engine may require priming prior to starting. To
prime the engine, proceed as follows:
C. Warm Engine Starting
1.
2.
Move control handle to the neutral detent position.
a.
b.
c.
Place ignition switch in the OFF position.
Disengage shift mechanism.
Turn key switch to START position and hold until
engine starts, but DO NOT hold in start position for
more than ten seconds. If engine does not start, let
go momentarily, then try again.
Move control handle to the full throttle position;
this operates accelerator pump and primes the
engine.
3.
As soon as engine starts, release key to the ON or
RUN position.
d.
e.
Repeat priming, if necessary.
NOTICE
NEVER turn key to START position when en-
gine is running.
Return the control handle to fast idle position.
2.
Turn key switch to START position and hold until
engine starts. DO NOT hold in START position for
more than ten seconds. In colder weather, more
primingmaybenecessary. However,toomuchprim-
ing may flood engine.
NOTICE
Warm engine starting procedures are different
for EFI engines. Refer to the engine owner’s
manual for additional information.
If engine floods:
•
Disengage shift. Move handle to full throttle posi-
tion.
Funship™ Owner’s Manual
Section A
Page 3
| Categories | Four Winns Freedom Manuals, Four Winns Funship Manuals, Four Winns Horizon Manuals, Four Winns Manuals, Outboard Marine Corporation Manuals |
|---|---|
| Tags | Four Winns Funship 214, Four Winns Funship 234, Four Winns Funship 264 |
| Model Year | 2003, 2004, 2005 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx |
| Document File Type | |
| Publisher | fourwinns.com |
| Wikipedia's Page | Outboard Marine Corporation |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)