FREQUENTLY ASKED QUESTIONS
No dealer-scheduled maintenance for the first three years of normal recreational use? Really?
•
Yes! Bombardier Recreational Products knows you want to spend your time on the water, not servicing your Evinrude
E-TEC outboard. There are no valves to adjust, belts to service, chains to replace, or oil to change. We do recommend
pre-launch inspections of your outboard at each use and at regular intervals. Salt water applications require minimal
additional inspections and lubrication.
What kind of oil does my Evinrude E-TEC outboard require?
•
Any TC-W3 oil may be used. The outboard can be programmed by your Dealer to run on Evinrude/Johnson XD100 oil
for lower oil consumption. Refer to FILLING THE OIL TANK on page 16; see also OIL REQUIREMENTS on page 16.
Do I need to mix oil into my fuel?
•
No. Evinrude E-TEC outboards do not require any mixing of oil and fuel.
What fuel octane is recommended for my Evinrude E-TEC outboard?
•
Evinrude E-TEC outboards require a minimum octane of 87 (U.S.). Use of higher octane fuels is not harmful, but also
not necessary. The use of alcohol-extended fuels is acceptable ONLY if the alcohol content does not exceed 10% eth-
anol by volume; or 5% methanol with 5% cosolvents by volume. Refer to Minimum Octane on page 17.
What do I need to do before storing my Evinrude E-TEC outboard for the winter?
•
Winterization is minimal. Refer to STORAGE on page 36 for step-by-step instructions to store your Evinrude E-TEC
outboard for the off-season.
Where should I take my Evinrude E-TEC outboard for service?
•
For repairs covered under warranty, you must take your Evinrude E-TEC outboard to an authorized dealer. BRP-ap-
proved dealers and distributors have received the necessary training to properly service your outboard. Contact BRP
for an authorized Evinrude E-TEC dealer near you.
Can I order replacement parts and accessories for my Evinrude E-TEC outboard?
•
Yes. When replacement parts are required, use Evinrude/Johnson Genuine Parts or parts with equivalent character-
istics, including type, strength, and material. Using substandard parts could result in injury or product malfunction. Your
dealer can order the parts and accessories you desire.
Do I need to complete any paperwork when I move or sell my Evinrude E-TEC outboard?
•
Yes. In order to maintain contact with you or the new Evinrude E-TEC outboard owner, BRP requests you complete
the form outlining CHANGE OF ADDRESS / CHANGE OF OWNERSHIP on page 63. This will ensure you or the new
owner is made aware of any product announcements and keep the warranty coverage up-to-date.
| Categories | Evinrude E-TEC Manual, Evinrude Outboard Manual |
|---|---|
| Tags | Evinrude 115 hp, Evinrude 130 hp, Evinrude 150 hp, Evinrude 175 hp, Evinrude 200 hp, Evinrude BX, Evinrude CX, Evinrude HL, Evinrude HX, Evinrude MX, Evinrude PL, Evinrude PX, Evinrude SL |
| Model Year | 2010 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(1 votes, average: 1 out of 1)
Marine readers have rated 2010 Evinrude 115 130 150 175 200 hp E-TEC PL PX SL BX HL HX CX MX Outboard Owners Manual 1.0 out of 1.0 based on 1 product reviews. OWNER OF A 2010 E-TEC 130 HP ON A WELD-CRAFT 18 FT BASS BOAT. A TOTAL WASTE OF GOOD MONEY. E-TEC IS THE WORST MOTOR ON THE MARKET. MINE OVERHEATS AND HAS LEFT ME STRANDED MANY TIMES. MAKE SURE YOU HAVE A GOOD TOW LINE IF YOU DECIDE TO BUY ONE.