X ENGINE MONITORING
Running Mode
ENGINE MONITORING SYSTEM
If any LED is ON while the outboard is run-
ning, it may indicate a system problem. Refer
to EMM Diagnostics Label.
Evinrude outboards equipped with remote
controls use the SystemCheck engine moni-
toring system.
LED 1, 2, or 3 ON, return to port as soon as
practical to avoid operational difficulties. See
your Dealer.
LED 4 ON indicates:
3
4
•
•
•
EMM temp. ABOVE range, refer to Engine
Overheating on page 41.
Engine temp. ABOVE range, refer to En-
gine Overheating on page 41.
Low / No Oil condition. Refer to Filling the
Oil Tank and Priming the Oil System on
page 19.
2
5
NO
WATER
CHECK
OIL
TEMP
ENGINE
1
6
LOW
OIL
0
7
LOW
OIL
NO
OIL
CHK
ENG
HOT
1
WARNING
Typical SystemCheck gauges
Do not run the engine in a low oil
condition for a long period of time. If
Self-Test
During engine start-up, pause with the key
run in excess of 4 hours, the engine switch in the ON position. The engine moni-
will shut down and will not restart. toring system self-tests the warning horn by
See dealer if engine shuts down.
sounding a half-second beep. The System-
Check gauge self-tests by turning the indica-
tor lights on simultaneously, then off in
sequence.
STARTING MODE
RUNNING MODE
-
-
-
-
CHARGING OKAY
- CHARGING FAULT
IMPORTANT: If the self-test does not happen
as stated, see your Dealer.
CRANK POSITION OKAY - INJECTOR / IGNITION FAULT
SENSORS OKAY
- SENSOR FAULT
LOW OIL Warning
The LOW OIL warning activates the warning
horn for 10 seconds and the low oil gauge
light for a minimum of 30 seconds.
LANYARD / STOP OKAY
- NO OIL / OVERHEAT
EMM DIAGNOSTICS
0
07057
EMM Diagnostics Label
The SystemCheck warning will reoccur at the
next startup if the problem is not corrected.
Start Mode
If the “LOW OIL” warning light illuminates, re-
fill the oil tank immediately. You have a limited
amount of normal operation before running
out of oil. Fill the oil tank with recommend oil
If any of the LEDs does NOT light during start-
ing, it may indicate an engine problem. Refer
to EMM Diagnostics Label.
LED 1, 2, or 3 OFF, seek assistance to return as soon as possible. Refer to Oiling System
to port. See your Dealer.
information on page 18.
LED 3 flashing indicates a hazardous fuel
condition may exist. Seek assistance to return
to port. See your Dealer.
LED 4 OFF indicates the stop circuit is activat-
ed, make sure the stop lanyard is attached.
“LOW OIL”
Low oil light is ON. Oil in the oil
Symptom
Result
tank is at reserve level or lower.
EMM will activate S.A.F.E.
mode soon.
LED 4 flashing indicates engine shut down:
•
•
•
EMM temp. OVER range, refer to Engine
Overheating on page 41.
Engine temp. OVER range, refer to Engine
Overheating on page 41.
Excessive No Oil condition. Seek assis-
tance to return to port.
Refill oil tank with the
recommended oil. If the oil tank
is full, return to safe harbor and
seek assistance.
Action
43
| Categories | BRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual |
|---|---|
| Tags | Evinrude 15 hp, Evinrude 25, Evinrude 30 hp, Evinrude DEL, Evinrude DHPL, Evinrude DHT, Evinrude DPL, Evinrude DR, Evinrude DRL, Evinrude DTE, Evinrude DTEL, Evinrude HTSL |
| Model Year | 2011 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)