2011 Four Winns H-Series Boat Owners Manual

For trailers, the steps to determining correct load limit
are:
dealer for  his  recommendation before  purchasing a
trailer hitch for your towing vehicle.
(1)
Locate the statement “The weight of
cargo should never exceed the XXX kg
or XXX lbs.” on your vehicle’s placard.
See Figure S1.
To help guard against a sudden failure while in
use, do not use a worn hitch ball.  Replace
all worn or damaged parts.
(2)
This figure equals the available amount
of cargo and luggage load capacity.
S - 2
TRAILER COMPONENTS
(3)
Determine the combined weight of
luggage and cargo being loaded on the
vehicle.  That weight may not safely
exceed the available cargo and luggage
load capacity.
A.   Bunk Supports
All bunk  boards are  made of pressure  treated wood.
This wood is rot resistant. All  boards are covered with
a high quality exterior grade carpet to protect  the boat
from damage during normal use.
Bunk supports run parallel to the keel and  support the
hull, extending beyond the transom.  See Figure S2.
Inner Bunks
Figure S1:  Vehicle Placard
Improper weight distribution can place excessive strain
on the towing vehicle and trailer.  It can also cause the
trailer to “fishtail” (sway side to side).  Be sure gear and
other items are distributed evenly in the boat.
Outer Bunks
Side Guides
Figure S2:  Trailer Bunks
C.   Hitches
Outerbunksupportsprovidestabilityfortheboat.     Thein-
side bunks are the main weight bearing members. Side
guide-on supports (certain models  only) help to keep
the boat straight while driving the boat onto the trailer.
Keeping the tie-downs tightly fastened will prevent the
boat from bouncing against the bunk supports.
The load-carrying  capacity of  trailer hitches  will vary
between manufacturers and must equal or exceed the
GVWR. Four Winns® trailers use surge brake systems
and require a fixed hitch.  Refer to Section S-2E Surge
Brakes for more information.
NOTICE
Improper trailer setup can cause hull damage.
Before hitching the trailer to the vehicle, make sure the
proper size hitch ball is installed to match the coupler.
The ball size is determined by the Gross Vehicle Weight
Rating or GVWR.  The GVWR is printed either on the
trailer plate  or embossed  on  the tongue,  coupler or
actuator.  For trailers with a GVWR of 7000 pounds or
less a 2” ball is  used.  For trailers with a GVWR over
B.   Tongue
Four Winns® trailers are designed with tongue weights
between 5% and 10%  of the total weight of the  boat,
fuel, gear and  trailer.  If the downward  weight on the
coupling ball  does not  fall within  this range,  coupler
failure and towing instability may occur. If using another
manufacturer’s trailer, have the dealer check the tongue
weight before trailering.
7000
pounds a 2 5/16” ball  is used.  This information
may also be obtained on our website at www.fourwinns.
com.   Refer to  Section  S-3 Operation  for additional
information on hitches. Also, consult your Four Winns
Trailer Information - Section S
Owner’s Manual Page 135
Product Specification
CategoriesFour Winns H-Series Manuals, Four Winns Manuals
Tags
Model Year2011
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 179 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandBoats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx
Document File TypePDF
Publisherfourwinns.com
Wikipedia's PageOutboard Marine Corporation
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website