Using Your Evinrude E-TEC Outboard
ENGINE OVERHEATING
NOTICE
To RESET the system:
even for a brief start-up—without supply- • The engine must be shut off and the cooling
temperature restored.
IF the S.A.F.E. mode activates and the
stream from the water pump indicator be-
comes intermittent or stops, reduce speed to
idle and:
Do not run your outboard—
ing water to it. Refer to Flushing on page
40.
IMPORTANT: Do not run your outboard—
even for a brief start-up—without supplying
water to it. Refer to Flushing on page 40.
While boating, the outboard’s water intakes
must stay completely submerged and unob-
structed. Observe proper transom height and
trim angle. While the outboard is running, the
1)
2)
3)
4)
Shift to NEUTRAL.
SHUT OFF the engine.
Tilt the outboard up.
Clean the intake screens of any blockage.
outboard’s water pump indicator must dis- 5) Clean the water pump indicator of any
charge a steady stream of water. Check the
blockage.
indicator often, especially when operating in 6) Lower the outboard.
weeds, mud and debris-laden water, and at 7) Restart the engine and run at idle.
extreme trim angles.
IF cleaning the screens and indicator does
not restore the water pump indicator’s steady
discharge, the engine will operate only in “get
home” mode. Return to harbor immediately.
See your Dealer.
IF cleaning the screens and indicator does
restore the water pump indicator’s steady
discharge, you might have to run for two min-
utes in NEUTRAL to allow the engine to cool
and the light to go off.
IMPORTANT: If cooling is not restored, the
EMM will identify a progressive overheating
condition and shut off the engine. The “WA-
TER TEMP” or “HOT” light will flash. The en-
gine will not restart until the engine is allowed
to cool.
1.
2.
Water intake screens
Water pump indicator
If the engine overheats, the engine monitor
will sound the warning horn and turn on the
“WATER TEMP” or “HOT” light. Also, the
S.A.F.E. (Speed Adjusting Failsafe Electron-
ics) mode will immediately limit the engine’s
speed to 1200 RPM. If the engine was run-
ning faster than 1200 RPM when the S.A.F.E.
mode activated, it will shake noticeably. The
protection system must be RESET before the
engine will operate at speeds over 1200 RPM.
Under certain conditions the EMM will shut off
the engine.
After any overheat causing engine shutdown,
see your Dealer for:
•
Inspection of the water pump for excessive
wear or damage.
•
Inspection of the thermostats.
IMPORTANT: Although the S.A.F.E. mode
can help prevent engine damage, it does not
guarantee you can run your engine indefinite-
ly without engine damage.
36
| Categories | BRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual |
|---|---|
| Document Type | Boat Motor Manual. Marine Operator's Engine Guide. |
| Tags | Evinrude 115 hp, Evinrude 130 hp, Evinrude 150 hp, Evinrude 175 hp, Evinrude 200 hp, Evinrude BX, Evinrude CX, Evinrude HL, Evinrude HX, Evinrude MX 60, Evinrude PL, Evinrude PX, Evinrude SL |
| Model Year | 2011 |
| Download File |
|
| Document File Type | |
| Publisher | evinrude.com |
| Wikipedia's Page | Evinrude Outboard Motors |
| Copyright | Attribution Non-commercial |
(4 votes, average: 4.25 out of 5)
Marine readers have rated 2011 Evinrude 115 130 150 175 200 hp E-TEC PL PX SL BX HL HX CX MX 60 Outboard Boat Motor Owners Manual 4.3 out of 5.0 based on 4 product reviews. Desidero avere il manuale per conoscere il tipo di motore.
Sono interessato alla conoscenza di questo tipo di motore.
no problems with my 130 etec so far. Its a 2011 model. Used in saltwater.
looking for the perfect manual