™
378
Yellowing is gel coat which has a yellow cast and strea-
king usually deals with a stain or contact with another
surface.
NOTICE
To preventgouges,unevenareas,orotherdam-
age from occurring, DO NOT use a power or
belt sander when sanding. For best results,
block sand the gel coat.
Gloss refers to the shine of the surface. This can change
from sanding action, chalk, residues, or exposure.
C. Stains
Blistering refers to a condition in which the unprotected
gel coat surface below the waterline has absorbed wa-
ter and formed bubbles. See Section P-5 for additional
information.
Stains can appear anywhere on the exterior of the boat
and may be a result of contact with tar, plant sap, leaves,
rust from metal fittings, and other materials. Surface
stains may be removed with hand dish washing soap,
mild cleansers, or some household detergents. DO NOT
use chlorine or ammonia products. These products can
affect the color of gel coat. Commercial car washes use
strong cleaners and should be avoided.
Follow the instructions below for boats that have weath-
ered and chalked.
1.
2.
Wash.
Wax. If this does not work, then use a fine rubbing
compound. If this does not work use 400 or 600 wet
ordrysandpaper,followedbyfinerubbingcompound
and wax.
To remove stains, refer to the procedures below.
1.
2.
Wash area with hand dish washing soap.
Begin with a small area such as three feet by three
feet and apply a mild cleanser.
When using wax or fine rubbing compounds, make sure
to read the label and follow the directions. Some helpful
tips are listed below.
3.
4.
Rinse with clean water.
1.
2.
Avoid working in direct sunlight. This dries out the
wax or compound, and can stain the surface.
Followwithcompoundandwaxingasoutlinedinpro-
cedure above.
Use clean pads or cloths to apply a thin coating of
wax or rubbing compound to a small area such as
three feet by three feet. Remove any excess, and
then rub the area with a buffing pad, or power buffer.
Apply pressure only as necessary to restore the sur-
face finish. Applying too much pressure or buffing
in one place too long can permanently damage the
surface.
If the stain is not removed by the hand dish washing
soap or mild cleanser, then the next procedure is to use
eitherdenaturedorrubbingalcohol. Ifthisdoesnotwork,
consult your Four Winns dealer for professional assis-
tance.
NOTICE
DO NOT use acetone, ketone, or other solvents
to remove stains. These chemicals are flam-
mable and may damage the gel coat.
3.
After applying compound, always follow with wax-
ing.
NOTICE
P - 5
FIBERGLASS REPAIRS
If using a power buffer, use a low RPM buffer
with light pressure. Keep the pad wet and the
buffermovingatalltimestopreventheatbuildup.
Fiberglass is one of the most durable, strong, and for-
giving construction materials afloat. It is resilient and
normalrepairscanbemadewithoutaffectingthestrength
or structural integrity of the boat.
378 Vista™ Owner’s Manual
Section P
Page 3
| Categories | Four Winns Manuals, Four Winns Vista Manuals, Outboard Marine Corporation Manuals |
|---|---|
| Tags | Four Winns Vista 378 |
| Model Year | 2002, 2003, 2004, 2005, 2006, 2007, 2008 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx |
| Document File Type | |
| Publisher | fourwinns.com |
| Wikipedia's Page | Outboard Marine Corporation |
| Copyright | Attribution Non-commercial |
(1 votes, average: 4 out of 4)
Marine readers have rated 2002-2008 Four Winns Vista 378 Boat Owners Manual 4.0 out of 4.0 based on 1 product reviews. great very informative. should not have to fill this out for a manule though