X ENGINE MONITORING
Running Mode
ENGINE MONITOR SYSTEM
If any LED is ON while the outboard is run- (OPTIONAL)
ning, it may indicate a system problem. Refer
This outboard can be equipped with an op-
tional engine monitoring system such as
to EMM Diagnostics Label.
LED 1, 2, or 3 ON, return to port as soon as I-Command, SystemCheck, or equivalent.
practical to avoid operational difficulties. See Use a monitoring system to provide visual
your Dealer.
and audible warnings.
LED 4 ON indicates:
IMPORTANT: Evinrude E-TEC 25 and 30 HP
EMM temp. ABOVE range, refer to Engine outboards require an optional module and
wire harness to support I-Command and Sys-
•
•
•
Overheating on page 41.
Engine temp. ABOVE range, refer to En- temCheck warning functions.
gine Overheating on page 41.
A dash-mounted gauge, a warning horn, a
CANmodule and related wiring are required.
Low / No Oil condition. Refer to Filling the
Oil Tank and Priming the Oil System on
page 17.
Gauges
WARNING
Gauges are available in several styles, such
as a digital I-Command gauge with LCD dis-
plays or a basic SystemCheck gauge.
Do not run the engine in a low oil con-
dition. If run in excess of 4 hours, the
engine will shut down and will not be
able to be restarted. See your Dealer.
STARTING MODE
RUNNING MODE
-
-
-
-
CHARGINGOKAY
- CHARGINGFAULT
CRANKPOSITIONOKAY - INJECTOR / IGNITIONFAULT
SENSORS OKAY
- SENSOR FAULT
1
2
LANYARD/ STOP OKAY - NOOIL/ OVERHEAT
1.
2.
Typical I-Command Digital gauge
Typical SystemCheck gauge
EMM DIAGNOSTICS
007057
EMM Diagnostics Label
For I-Command and other gauges, refer to the
gauge user’s guide for gauge displays, oper-
ation, warnings, and monitoring instructions.
Start Mode
If any of the LEDs does NOT light during start-
ing, it may indicate an engine problem. Refer
to EMM Diagnostics Label.
LED 1, 2, or 3 OFF, seek assistance to return
to port. See your Dealer.
LED 3 flashing indicates a hazardous fuel
condition may exist. Seek assistance to return
to port. See your Dealer.
Self-Test
During engine start-up, pause with the key
switch in the ON position. The monitoring sys-
tem self-tests by sounding a half-second
beep. SystemCheck gauges self-test by turn-
ing the indicator lights on simultaneously,
then off in sequence.
LED 4 OFF indicates the stop circuit is activat-
ed, make sure the stop lanyard is attached.
LED 4 flashing indicates engine shut down:
IMPORTANT: If the self-test does not happen
as stated, see your Dealer.
•
•
•
EMM temp. OVER range, refer to Engine
Overheating on page 41.
Engine temp. OVER range, refer to Engine
Overheating on page 41.
Excessive No Oil condition. Seek assis-
tance to return to port.
39
| Categories | BRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual |
|---|---|
| Tags | Evinrude 25 hp, Evinrude 30 hp, Evinrude PL, Evinrude RL, Evinrude TE, Evinrude TEL |
| Model Year | 2009 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(2 votes, average: 4 out of 5)
Marine readers have rated 2009 Evinrude 25 30 hp E-TEC RL TE TEL PL Outboard Boat Owners Manual 4.0 out of 5.0 based on 2 product reviews. I can not get an owners manual for my motor, it is an 2015 Evinrude e-tec , 2 stroke 25 hp
Thank you very much for having this service of free downloads of ETEC manuals.