2008 Evinrude 200 225 250 hp E-TEC PL PX PZ CX CZ HL HX HSL Outboard Boat Owners Manual

   Using Your E-TEC Outboard
The following warnings may appear on the engine monitor gauge.
“LOW OIL”
Symptom
Result
Oil in the oil tank is at reserve level (about 1/4 full)
EMM will activate low oil light or display warning
Fill the oil tank with recommended oil as soon as possible to avoid emptying
the  tank. The  outboard  has  approximately five  hours  (ten  hours if  using
Evinrude/Johnson XD100 oil) of normal running time before “NO OIL” condi-
tion occurs. Refer to Filling the Oil Tank on page 15.
Action
“NO OIL”
Symptom
Result
There is an oil delivery problem
EMM will activate S.A.F.E.* mode
If the oil tank is empty, add the recommended oil.
If the oil tank is not empty, seek assistance and/or return to safe harbor.
Action
Your outboard is designed to run in “get home” mode for up to five hours in the event you run
out of oil. Refill the oil tank. Prime oil system. Refer to Priming the Oil System on page 15.
“WATER TEMP” or “HOT”
Symptom
Result
The engine is overheating
EMM will activate S.A.F.E.* mode
A continuous light with S.A.F.E. mode — The  EMM has identified an over-
heating condition. Check the water pump indicator for a steady stream of wa-
ter. Shut OFF the engine. Clear the water intake screens of any debris. If the
overheat condition still exists, the engine will operate in “get home” mode. Re-
turn to harbor immediately.
Action
A flashing light  — The EMM has identified  a damaging overheating condi-
tion. The engine will not operate. Allow the engine to cool for 20 minutes and
return to harbor immediately. See your Dealer.
“CHECK ENGINE” or “CHK ENG”
Symptom
Result
An abnormal operating condition
EMM will activate check engine light or display warning
A flashing light — The EMM has identified an abnormal operating condition
related to the fuel system. The engine will shut OFF and cannot be restarted.
A continuous light with S.A.F.E. mode — The EMM has identified a problem
with the outboard. Seek assistance and/or return to harbor. See your Dealer.
A continuous light without S.A.F.E. mode — The EMM has identified a prob-
lem that should  be addressed by your Dealer  as soon as practical  to avoid
operational difficulties.
Action
WARNING
If the outboard  shuts OFF and the  “CHECK ENGINE” or “CHK  ENG” light is flash-
ing, the outboard  cannot be restarted. A hazardous  fuel condition may exist. Seek
assistance to return to port.
*Speed Adjusting Failsafe Electronics
18
Product Specification
CategoriesBRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual
Tags, , , , , , , , , ,
Model Year2008
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 62 pages
Document File TypePDF
CopyrightAttribution Non-commercial
(1 votes, average: 3 out of 3)
Marine readers have rated 2008 Evinrude 200 225 250 hp E-TEC PL PX PZ CX CZ HL HX HSL Outboard Boat Owners Manual 3.0 out of 3.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

2008 Evinrude 200 225 250 hp E-TEC PL PX PZ CX CZ HL HX HSL Outboard Boat Owners Manual SKU UPC Model
Rob on Jul 15, 2015.

I have not seen the manual yet. Very difficult to post a review at this point.


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website