Using Your E-TEC Outboard
OIL AND FUEL
OIL REQUIREMENTS
OILING SYSTEM
Evinrude/Johnson Brand Oils
If the “LOW OIL” warning light illuminates,
you have approximately five hours of normal
operation before running out of oil. Refill the
oil tank at next convenient opportunity.
deposits, providing superior lubrication, and Always “top off” your oil tank prior to pro-
longed usage or long trips.
Evinrude/Johnson outboard oils are formulat-
ed to give best engine performance while
controlling piston and combustion chamber
ensuring maximum spark plug life.
The following outboard oils are recommend- New outboards are programmed to use addi-
ed for use in your Evinrude E-TEC outboard: tional oil during the first two hours of opera-
tion above 2000 RPM.
•
•
•
Evinrude/Johnson XD100;
Evinrude/Johnson XD50; or
Evinrude/Johnson XD30.
IMPORTANT: When operating in conditions
under 32°F (0°C), Evinrude/Johnson XD100
oil must be used.
Evinrude/Johnson XD100 Oil
If the oil hose is disconnected for any reason,
seal it to prevent spillage. Install a cap on the
hose fitting to prevent contamination.
You must use an oil tank equipped with a filter
and an oil supply hose. The oil system must
be purged if air is in the oil supply hose. Refer
to Priming the Oil System on page 15.
Evinrude/Johnson XD100 oil is preferred
for your Evinrude E-TEC outboard. This
synthetic formula oil provides uncompro-
mised lubrication and superior performance,
even in extreme conditions—especially in
cold temperatures down to 0°F (-17°C).
If requested, an authorized dealer can pro-
gram your Evinrude E-TEC outboard EMM
for the exclusive use of Evinrude/Johnson
XD100. Only an authorized Evinrude deal-
er can program your outboard for this op-
tional benefit.
Oil consumption is reduced if the outboard is
programmed for exclusive use of Evinrude/
Johnson XD100 as compared to using a con-
ventional oil.
IMPORTANT: If your EMM has been pro-
grammed for Evinrude/Johnson XD100,
DO NOT use any other oil unless in an emer-
gency. If Evinrude/Johnson XD100 is tempo-
rarily unavailable, a one-time-only use of an
oil that meets NMMA TC-W3 certification Install the oil tank following the instructions
standards is allowed. If you discontinue using provided with the unit.
Evinrude/Johnson XD100, you MUST first re-
IMPORTANT: Consider the installation loca-
turn to your Dealer to have the EMM repro-
tion of the oil tank carefully. The oil tank is
grammed back to the original factory setting.
vented to the atmosphere. To avoid serious
powerhead damage, be sure the oil tank is in-
Other Oils
If Evinrude/Johnson brand oils are not avail-
able, you must use an oil that meets NMMA
stalled in a location that does not allow con-
stant exposure to sunlight, rain, bilge water, or
spray. Periodically inspect the oil tank for evi-
TC-W3 certification standards.
dence of water.
IMPORTANT: Failure to follow oil specifica-
tions could void the engine warranty if a lubri-
cation-related failure occurs.
14
| Categories | BRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual |
|---|---|
| Tags | Evinrude 200 hp, Evinrude 225 hp, Evinrude 250 hp, Evinrude CX, Evinrude CZ, Evinrude HL, Evinrude HSL, Evinrude HX, Evinrude PL, Evinrude PX, Evinrude PZ |
| Model Year | 2008 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(1 votes, average: 3 out of 3)
Marine readers have rated 2008 Evinrude 200 225 250 hp E-TEC PL PX PZ CX CZ HL HX HSL Outboard Boat Owners Manual 3.0 out of 3.0 based on 1 product reviews. I have not seen the manual yet. Very difficult to post a review at this point.