required.by.the.indications.on.the.dip.sticks...
Refer.to.Table.1:.“SAE.Viscosity.Chart”.and.your.
engine.manual.included.in.the.owner’s.packet..
Follow.engine.manufacturer’s.recommendations..
If engine floods:
•.
Disengage.shift..Move.handle.to.full.throttle.
position.
.
DO.NOT.USE.MULTIGRADE.OIL..Power.steering.
and power trim use automatic transmission fluid.
Check the fluid levels in the vertical drive units or
transmission.as.often.as.practical.
•.
•.
Turn.key.switch.to.the.START.position.
Immediately.move.the.control.handle.to.the.neutral.
detent.(idle).position.when.the.engine.starts.
NOTICE
THE FOLLOWING
IF THE LOWEST
SAE VISCOSITY
ANTICIPATED
TEMPERATURE IS*
RECOMMENDED
Failure to move the control handle to the idle
position immediately when engine starts will
allow engine to “over-rev” and engine damage
could result. “Over-revving” engine after off-
season storage could also damage the water
pump impeller. When starting engine for the
first time after off-season storage, always idle
engine for one minute to allow the water
pump to prime.
OILS ARE
3
2
O
F (0
o
C) and above
F (0 C)
O
SAE 30
SAE 20W-20
SAE 10W
0
O
F (-18 C) to 32
O
O
Below 0 F (-18 C)
O O
*
Temperature range you expect to operate.
Note: Use only single viscosity oils.
.
Table 1: SAE Viscosity Chart
3..
Start.and.operate.the.bilge.blower.system.for.at.
least.four.(4).minutes.before.start-up.
3.. As.soon.as.engine.starts:
.
4..
Lower.the.vertical.outdrive.units.(on.applicable.
models).making.sure.the.water.intakes.are.under..
the.water.
a.. Release.key.to.the.ON.or.RUN.position.
b.. Move.control.handle.to.the.fast.idle.position.to.
warm.up.engine..DO.NOT.exceed.1000.RPM.
B. Cold Engine Start (Carbureted Engines)
C. Cold Engine Start (Carbureted Engines with
“Turn Key Start”)
1..
The.engine.may.require.priming.prior.to.starting...
To.prime.the.engine,.proceed.as.follows:
1.
2.
Place.the.remote.control.handle.in.neutral.
a... Place.ignition.switch.in.the.OFF.position.
b... Disengage.shift.mechanism.
Turn.ignition.key.to.START..Release.key.when.
engine.starts.and.allow.switch.to.return.to.ON.po-
sition..Allow.engine.to.warm.up.(6-10.minutes.on.
first start of the day). The engine will normally idle
at.900-1000.RPM.and.then.return.to.normal.idle.
RPM.of.approximately.750.RPM.
c... Move.control.handle.to.the.full.throttle..
position;.this.operates.accelerator.pump..
and.primes.the.engine.
d.. Repeat.priming,.if.necessary.
3.. If.engine.does.not.start.after.3.attempts:.
e.. Return.the.control.handle.to.neutral.detent..
(idle).position.
a.. Push.the.throttle.only.button.and.position.the..
remote.control.handle/throttle.lever.to.the1/4.
throttle.position.
2..
Turn.key.switch.to.START.position.and.hold.until.
engine.starts..DO.NOT.hold.in.START.position.for.
more.than.ten.seconds..In.colder.weather,.more.
priming.may.be.necessary..However,.too.much.
priming may flood engine.
b.. Turn.ignition.key.to.START..Release.key.
when.engine.starts.and.allow.switch.to.return.
to.ON.position.
Operation - Section A
Owner’s Manual Page
| Categories | Four Winns Manuals, Four Winns Vista Manuals, Outboard Marine Corporation Manuals |
|---|---|
| Tags | Four Winns Horizon 180, Four Winns Horizon 183, Four Winns Horizon 190, Four Winns Horizon 200, Four Winns Horizon 203, Four Winns Horizon 210, Four Winns Horizon 220, Four Winns Horizon 240, Four Winns Horizon 260 |
| Model Year | 2006, 2007, 2008 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx |
| Document File Type | |
| Publisher | fourwinns.com |
| Wikipedia's Page | Outboard Marine Corporation |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)