™
2.
3.
Slide the trailer tongue into the receiver until the
clevis pin holes are aligned.
Insert clevis pins with washers and locking hair pins.
NOTICE
Thetonguewillexertsomepressureontheclevis
pins. It may be necessary to lift, push or wiggle
the tongue to insert the clevis pins.
4.
5.
Reconnect the brake line coupler.
If towing the trailer, remember to plug the 5-wire
tongue harness to the trunk connector wire harness
of your tow vehicle.
Figure S2: Trailer Tongue Assembly
Make sure the trailer tongue is secure before
hitching to the towing vehicle.
To pivot the tongue on trailers models with hinge located
inside the receiver:
To pivot the tongue on trailers models with exposed
hinges:
1.
Make sure the trailer jack is supporting the trailer
loadproperly. RefertoSectionS-2C onSwivelJacks
for additional information.
1.
Make sure the trailer jack is supporting the trailer
loadproperly. RefertoSectionS-2ConSwivelJacks
for additional information.
2.
3.
4.
Unplug the wire harness at the trailer cross member.
Disconnect the brake line coupler.
2.
3.
4.
Unplug the wire harness at the trailer cross member.
Disconnect the brake line coupler.
Removethelocking hair pins andclevispins. Please
note, the locking hair pins must be rotated away
from clevis pin and then removed.
Remove the clevis pin keeper and clevis pin.
NOTICE
NOTICE
Thetonguewillexertsomepressureontheclevis
pins. It may be necessary to lift, push or wiggle
the tongue to remove the clevis pins.
Thetonguewillexertsomepressureontheclevis
pins. It may be necessary to lift, push or wiggle
the tongue to remove the clevis pins.
5.
Pivot the tongue towards the trailer as far as it will
go.
5.
Slide trailer tongue out of receiver until the hinge is
exposed. Pivot the tongue towards the trailer as
far as it will go.
To reinstall, follow this procedure in reverse order.
To reinstall, follow this procedure in reverse order.
1.
Pivot the tongue until the clevis pin hole is aligned.
1.
Pivot the tongue so that it extends straight and is in
alignment with the receiver.
NOTICE
When extending tongue ensure that the brake
line and wire harness are not pinched. Failure
to check could result in damage.
NOTICE
When extending tongue ensure that the brake
line and wire harness are not pinched. Failure
to check could result in damage.
Freedom™/Horizon™ Owner’s Manual
Section S
Page3
| Categories | Four Winns Freedom Manuals, Four Winns Horizon Manuals, Four Winns Manuals, Outboard Marine Corporation Manuals |
|---|---|
| Tags | Four Winns Freedom 170, Four Winns Freedom 180, Four Winns Horizon 170, Four Winns Horizon 180, Four Winns Horizon 190, Four Winns Horizon 200, Four Winns Horizon 210, Four Winns Horizon 230, Four Winns Horizon 250, Four Winns Horizon 280 |
| Model Year | 2003, 2004, 2005 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx |
| Document File Type | |
| Publisher | fourwinns.com |
| Wikipedia's Page | Outboard Marine Corporation |
| Copyright | Attribution Non-commercial |
(1 votes, average: 2 out of 2)
Marine readers have rated 2003-2005 Four Winns Horizon 170 180 190 200 210 230 250 280 Freedom 170 180 Owners Manual 2.0 out of 2.0 based on 1 product reviews.