4.
Rotate the bucket seat inboard (towards the cen-
ter of the boat) until it faces as far aft as possible or
desired. Once in position, push down on locking
lever to lock seat in position. See Figure N8.
4. Position the seat forward or aft according to the
needs of the individual by using the lever located
underneath the seat. See Figure N6.
5.
Tilt the steering wheel (if applicable) to the desired
position using the tilt lever knob on the steering col-
umn.
After rotating, lock seat in place securely. Sud-
den acceleration with seat unlocked could
cause loss of balance and possible injury.
DO NOT sit on the backrest portion of any cock-
pit seat. The operator could lose control of boat
or passengers could be thrown from boat. Also,
the seat may be damaged from improper use.
Pull lever to
up position
to rotate seat.
E. Double-Wide Helm Seat
On certain Horizon™ models, a standard double-wide
helm seat with a flip-up bolster is standard. To adjust
the helm seat push out on the locking lever under the
seat, on the right. Slide the seat forward or aft to the
desired position. The seat will adjust approximately six
(6) inches. This helm seat does not swivel.
Friction
Adjustment
Knob
Figure N7: Swivel Position
F.
Stern (Jump) Seats
Once in desired
position push
lever down
to lock seat
in place.
On certain standard interiors, the motorhood and two
jumpseats are installed at the stern. The jumpseats, in
thelower positionsaresupportedbythemotorhoodbase
and ski rack (lower upholstered pad) and/or liner. Only
on certain models can the jumpseat be placed in an
upper position to create a sunpad.
Figure N8: Locking Position
To install the jumpseats in the upper position (if appli-
cable):
To return the bucket seat to the bow facing position:
1.
2.
Remove the jumpseat from the lower position.
1.
2.
3.
Slide the seat completely forward or rearward (as
needed to clear coaming/side pad or seat cushion)
by using the lever located underneath the seat. See
Figure N6.
Place the cleat of the jumpseat into the upper re-
cessed portion of the motorhood.
3.
Push opposite end of the jumpseat into position.
The fit should be snug and relatively flush with
motorhood pad.
Locate thelever on the right side of the bucket slider
mechanism and lift upward to release the pin from
the pedestal. This will allow you to rotate the seat.
See Figure N7.
Rotate the bucket seat inboard until it is in the for-
ward facing position. Once in position, push down
on locking lever to lock seat in position. See Fig-
ure N8. In addition, DO NOTUSE FORCE to rotate
the chair.
To prevent personal injury, be sure the jump
seats are secure before use. Do not step or
walk on jumpseats. Jumpseats could move
and cause loss of balance.
Freedom™/Horizon™ Owner’s Manual
Section N
Page 3
| Categories | Four Winns Freedom Manuals, Four Winns Horizon Manuals, Four Winns Manuals, Outboard Marine Corporation Manuals |
|---|---|
| Tags | Four Winns Freedom 170, Four Winns Freedom 180, Four Winns Horizon 170, Four Winns Horizon 180, Four Winns Horizon 190, Four Winns Horizon 200, Four Winns Horizon 210, Four Winns Horizon 230, Four Winns Horizon 250, Four Winns Horizon 280 |
| Model Year | 2003, 2004, 2005 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx |
| Document File Type | |
| Publisher | fourwinns.com |
| Wikipedia's Page | Outboard Marine Corporation |
| Copyright | Attribution Non-commercial |
(1 votes, average: 2 out of 2)
Marine readers have rated 2003-2005 Four Winns Horizon 170 180 190 200 210 230 250 280 Freedom 170 180 Owners Manual 2.0 out of 2.0 based on 1 product reviews.