Blistering refers to a condition in which the unprotected C. Stains
gel coat surface below the waterline has absorbed water
andformedbubbles. SeeSectionP-5foradditionalinfor- Stains can appear anywhere on the exterior of the boat
mation.
and may be a result of contact with tar, plant sap, leaves,
rust from metal fittings, and other materials. Surface
Follow the instructions below for boats that have weath- stainsmayberemovedwithhanddishwashingsoap,mild
ered and chalked.
cleansers, or some household detergents. DO NOT use
chlorine or ammonia products. These products can af-
fect the color of gel coat. Commercial car washes use
strong cleaners and should be avoided.
1.
2.
Wash.
Wax. If this does not work, then use a fine rubbing
compound. If this does not work use 400 or 600 wet To remove stains, refer to the procedures below.
ordrysandpaper,followedbyfinerubbingcompound
and wax.
1. Wash area with hand dishwashing soap.
When using wax or fine rubbing compounds, make sure 2. Begin with a small area such as three feet by three
to read the label and follow the directions. Some helpful
tips are listed below.
feet and apply a mild cleanser.
Rinse with clean water.
3.
1.
2.
Avoid working in direct sunlight. This dries out the
wax or compound, and can stain the surface.
4. Followwithcompoundandwaxingasoutlinedinpro-
cedureabove.
Use clean pads or cloths to apply a thin coating of
wax or rubbing compound to a small area such as If the stain is not removed by the hand dishwashing soap
three feet by three feet. Remove any excess, and or mild cleanser, then the next procedure is to use either
then rub the area with a buffing pad, or power buffer. denatured or rubbing alcohol. If this does not work, con-
Apply pressure only as necessary to restore the sur- sult your Four Winns dealer for professional assistance.
face finish. Applying too much pressure or buffing in
oneplacetoolongcanpermanentlydamagethesur-
face.
NOTICE
DO NOT use acetone, ketone, or other solvents
to remove stains. These chemicals are flam-
mable and may damage the gel coat.
3.
After applyingcompound, always followwithwaxing.
NOTICE
If using a power buffer, use a low rpm buffer with
light pressure. Keep the pad wet and the buffer
moving at all times to prevent heat build up.
P - 5 FIBERGLASSREPAIRS
Fiberglass is one of the most durable, strong, and forgiv-
ing construction materials afloat. It is resilient and nor-
mal repairs can be made without affecting the strength or
structural integrity of the boat.
NOTICE
To preventgouges,unevenareas,orotherdam-
agefrom occurring, DONOTuseapowerorbelt
sander when sanding. For best results, block
sand the gel coat.
Striking docks, other boats, or submerged ob-
jects could create a very hazardous situation or
severely damage the fiberglass. In the event an
object is struck below or near the waterline, pro-
ceed directly and cautiously to the nearest ser-
vice facility and remove the boat from the water.
Closely inspect the hull for damage. If the outer
fiberglasslaminatewaspenetrated,repairsmust
be made prior to relaunch.
Freedom™/Horizon™ Owner’s Manual
Section P
Page 3
| Categories | Four Winns Freedom Manuals, Four Winns Horizon Manuals, Four Winns Manuals, Outboard Marine Corporation Manuals |
|---|---|
| Tags | Four Winns Freedom 170, Four Winns Freedom 180, Four Winns Horizon 170, Four Winns Horizon 180, Four Winns Horizon 190, Four Winns Horizon 200, Four Winns Horizon 210, Four Winns Horizon 230, Four Winns Horizon 250, Four Winns Horizon 280 |
| Model Year | 2003, 2004, 2005 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx |
| Document File Type | |
| Publisher | fourwinns.com |
| Wikipedia's Page | Outboard Marine Corporation |
| Copyright | Attribution Non-commercial |
(1 votes, average: 2 out of 2)
Marine readers have rated 2003-2005 Four Winns Horizon 170 180 190 200 210 230 250 280 Freedom 170 180 Owners Manual 2.0 out of 2.0 based on 1 product reviews.