Yellowing is gel coat which has a yellow cast and strea-
king usually deals with a stain or contact with another
surface.
NOTICE
When sanding, DO NOT use a power or belt
sander to prevent gouges, uneven areas, or
other damage. For best results, block sand the
gel coat.
Gloss refers to the shine of the surface. This can change
from sanding action, chalk, residues, or exposure.
C. Stains
Blistering refers to a condition in which the unprotected
gel coat surface below the waterline has absorbed wa-
ter and formed bubbles. See Section P-5 for additional
information.
Stains can appear anywhere on the exterior of the boat
and may be a result of contact with tar, plant sap, leaves,
rust from metal fittings, and other materials. Surface
stains may be removed with hand dishwashing soap,
mild cleansers, or some household detergents. DO NOT
use chlorine or ammonia products. These products can
affect the color of gel coat. Commercial car washes use
strong cleaners and should be avoided.
Follow the instructions below for boats that have weath-
ered and chalked.
1.
2.
Wash.
Wax. If this does not work, then use a fine rubbing
compound. If this does not work use 400 or 600 wet
ordrysandpaper,followedbyfinerubbingcompound
and wax.
To remove stains, refer to the procedures below.
1.
2.
Wash area with hand dishwashing soap.
Begin with a small area such as three feet by three
feet and apply a mild cleanser.
When using wax or fine rubbing compounds, make sure
to read the label and follow the directions. Some helpful
tips are listed below.
3.
4.
Rinse with clean water.
1.
2.
Avoid working in direct sunlight. This dries out the
wax or compound, and can stain the surface.
Follow with compound and waxing as outlined in
procedure above.
Use clean pads or cloths to apply a thin coating of
wax or rubbing compound to a small area such as
three feet by three feet. Remove any excess, and
then rub the area with a buffing pad, or power buffer.
Apply pressure only as necessary to restore the sur-
face finish. Applying too much pressure or buffing
in one place too long can permanently damage the
surface.
If the stain is not removed by the hand dishwashing soap
or mild cleanser, then the next procedure is to use either
denatured or rubbing alcohol. If this does not work, con-
sultyourFourWinns® dealerforprofessionalassistance.
NOTICE
DO NOT use acetone, ketone, or other solvents
to remove stains. These chemicals are flam-
mable and may damage the gel coat.
3.
After applying compound, always follow with wax-
ing.
P - 5
FIBERGLASS REPAIRS
NOTICE
If using a power buffer, use a low RPM buffer
with light pressure. Keep the pad wet and the
buffer moving at all times to prevent heat build
up.
Fiberglass is one of the most durable, strong, and for-
giving construction materials afloat. It is resilient and
normalrepairscanbemadewithoutaffectingthestrength
or structural integrity of the boat.
Candia FS Owner’s Manual
03/00
Section P
Page 3
| Categories | Four Winns Funship Manuals, Four Winns Manuals, Outboard Marine Corporation Manuals |
|---|---|
| Tags | Four Winns Funship 214, Four Winns Funship 234, Four Winns Funship 254 |
| Model Year | 1998, 1999, 2000, 2001, 2002 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx |
| Document File Type | |
| Publisher | fourwinns.com |
| Wikipedia's Page | Outboard Marine Corporation |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)