1998-2002 Four Winns Funship 214 234 254 Owners Manual

To pivot the tongue on painted trailers for storage:
To remove the tongue on galvanized trailers:
1.
Make sure the  trailer jack is supporting  the trailer
loadproperly.  RefertoSectionS-2C  onSwivelJacks
for additional information.
1.
Make sure the  trailer jack is supporting  the trailer
loadproperly.  RefertoSectionS-2ConSwivelJacks
for additional information.
2.
Unplug the wire harness at the  trailer cross mem-
ber.
2.
Unplug the wire harness at the  trailer cross mem-
ber.
3
.
Disconnect the brake line coupler.
3.
4.
Disconnect the brake line coupler.
4.
Removethelocking  hair pins andclevispins. Please
note, the locking  hair pins must  be rotated away
from clevis pin and then removed.
Remove the ring cotters and clevis pins.
NOTICE
The tongue  will exert  some pressure  on the
clevis pins. It may be necessary to lift, push or
wiggle the tongue to remove the clevis pin.
NOTICE
The tongue  will exert  some pressure  on the
clevis pins. It may be necessary to lift, push or
wiggle the tongue to remove the clevis pins.
5.
Slide trailer  tongue out of  receiver and store in  a
proper place.   If the  trailer has brakes,  store the
tongue upright to prevent brake fluid from leaking.
5.
Slide trailer tongue out of receiver until the hinge is
exposed.   Pivot the tongue towards the trailer as
far as it will go.
To reinstall, follow this procedure in reverse order.
To reinstall, follow this procedure in reverse order.
Make sure the trailer tongue is secure before
hitching to the towing vehicle.
1.
Pivot the tongue so that it extends straight and is in
alignment with the receiver.
NOTICE
C.   Swivel Jack
When extending tongue ensure that the brake
line and wire harness are not pinched. Failure
to check could result in damage.
Thejackisdesignedtolift,lowerandsupportthetongues
of the trailers when not connected to the towing vehicle.
Before unhitching the trailer, use the following guidelines
when setting up the jack.
2.
3.
Slide the trailer tongue into the receiver until the
clevis pin holes are aligned.
1.
2.
Pull on the lock pin. See Figure S3.
Swivel jack to the vertical position.
Insert clevis pins with washers and locking hair pins.
NOTICE
The tongue  will exert  some pressure  on the
clevis pins. It may be necessary to lift, push or
wiggle the tongue to insert the clevis pins.
4.
5.
Reconnect the brake line coupler.
If towing the  trailer, remember to plug  the 5-wire
tongue harness  to the trunk  connector wire  har-
ness of your tow vehicle.
Make sure the trailer tongue is secure before
hitching to the towing vehicle.
Figure S3: Swivel Jack
Candia FS Owner’s Manual
03/00
Section S
Page 3
Product Specification
CategoriesFour Winns Funship Manuals, Four Winns Manuals, Outboard Marine Corporation Manuals
Tags, ,
Model Year1998, 1999, 2000, 2001, 2002
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 139 pages
Document TypeOwner's Manual
LanguageEnglish
Product BrandBoats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx
Document File TypePDF
Publisherfourwinns.com
Wikipedia's PageOutboard Marine Corporation
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website