3.
Wax.
glass gel coat to the repaired area. Enough gel
coat should be used so that the entire area is
covered. The gel coat must be catalyzed using up
to 2% MEK Peroxide which can be purchased at a
supplier handling fiber glass rein fo rced products.
Contact your Four Winns dealer for assistance.
If this does not work, clean the area and sand lightly
with 400 to 600 wet or dry sandpaper and follow with
rubbing compound and wax.
B. Gouges & Cracks
8.
After ample drying time, sand the area using very
fine wet/dry sandpaper. If the appear ance of the
area is still not satisfactory, repeat steps 2 through
4 as necessary.
Stress cracks and crazing are the appearance of
hairline cracks in the gel coat surface. When present,
these problems usually occur in the gel coat finish or
the outer “skin coat” fiberglass laminate. The appear-
ance of these cracks does not pose a threat to the
structural integrity of the boat. In most cases, they
are cosmetic and can be treated.
9. If above the waterline, polish the area using a
fiberglass rubbing compound and then wax. If the
repaired area is below the waterline, the area
should be primed and painted in accordance with
the anti-fouling paint manufacturer’s instructions.
Cosmetic surface damage can be repaired as follows:
1.
Sand the surrounding area with medium or fine
grit sandpaper. Clean all marine growth, dirt,
anti-fouling paint, etc. from the immediate area.
DO NOT excessively scratch or gouge the
surrounding area.
Gel coat, like paint, will change colors with time and
exposure to sunlight (ultraviolet). For this reason,
“matching” gel coat obtained from Four Winns may
not match the gel color of a boat that has been
exposed. However, this is the closest match commer-
cially available. A fiberglass technician can tint the gel
to be used in the repair to provide a closer color
match.
2.
3.
4.
Use a hard, pointed tool to open the gel crack.
Take care not to damage the surrounding gel coat.
Sand the crack or gouge so the edges are smooth
and will allow proper “feathering” of the area.
More severe fiberglass damage, especially when
structural, requires the expertise of an experienced
fiberglass repair technician. See your Four Winns
dealer for assistance.
Clean the area thoroughly. Make sure the area is
dry before proceeding.
NOTICE
Improper repair techniques can lead to further
fiberglass component damage.
NOTICE
Be sure the structure and the ambient
temperature are above 60 degrees F (15
degrees C) and the relative humidity below
C. Osmotic Blistering
70%
immediately before, during, and after the
repair.
Osmotic blistering or “boat pox” is an unfortunate
but not uncommon occurrence in fiberglass boats.
Fiberglass is water retardant, not waterproof. When
a boat is left in the water for a period of time, the
fiberglass will absorb water. It is a natural process
that can not be eliminated in production methods or
material selection and usage. However, there are
ways to control and possibly prevent blisters (see Sec-
tion P-6). If you do encounter blisters, be assured that
the blisters are merely cosmetic. They do not indicate
a defect in the boat structure or lamination. Four
Winns, along with most boat manufacturers, regard
gel blisters as a standard maintenance item.
5.
If the nick or gouge is deep and penetrates
through the gel coat, fill the area with fiber glass
patching paste. Follow the directions on the can
when mixing the paste with the catalyst.
6.
After the gouge is filled and has dried, sand the
patched area. Begin by using medium-fine grade
sandpaper. Progres sively use finer grade sandpa-
per until the surface is very smooth. If necessary,
add filler and then sand the surface again.
7.
Apply two or three light coats of matching fiber-
Fiberglass & Hull Information - Section P
Owner’s Manual Page 146
| Categories | Four Winns Manuals, Four Winns V-Series Manuals |
|---|---|
| Tags | Four Winns V475 |
| Model Year | 2011 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx |
| Document File Type | |
| Publisher | fourwinns.com |
| Wikipedia's Page | Outboard Marine Corporation |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)