X STORAGE
4)
Allow outboard to run until it shuts itself
OFF automatically (less than one minute).
Winterization is complete when outboard
shuts itself off.
Winterization is complete when outboard
shuts itself off.
• If the outboard DOES NOT shut itself
off, you may not have allowed enough run-
ning time at a throttle position.
•
If the outboard DOES NOT shut itself
off, you may not have properly advanced
throttle grip.
If the engine exceeds 3000 RPM, the out-
board may have been shifted into gear.
•
In either event, immediately press STOP • If the engine exceeds 3000 RPM, the out-
button to turn outboard OFF and re-start the
procedure.
board may have been shifted into gear.
In either event, immediately turn key switch
OFF and re-start the procedure.
Remote Control Outboards with Foot
Throttle
After Winterization – All Outboards
1)
After the outboard shuts itself off, turn key
switch OFF. (For tiller models, remove
emergency stop clip / key switch.) Do not
start the outboard again after winterization
is completed.
1)
Press foot throttle to HALF THROTTLE po-
sition. Start the outboard. Outboard runs at
slow idle speed.
2)
If winterizing on a trailer, turn off water
and detach garden hose. Grease propeller
shaft splines with recommended lubricant,
and re-install propeller.
IMPORTANT: When winterizing is finished,
leave the outboard in vertical position long
enough to completely drain the powerhead. If
equipped, disconnect the speedometer pick-
up at the upper connection and blow all water
Foot Throttle – Typical
2)
After outboard runs for about 15 seconds, out of the hose using air pressure of 25 psi or
remove foot from foot throttle and allow less. Reconnect speedometer pickup after all
throttle to return to IDLE position. Outboard the water has been removed.
continues to run at slow idle speed.
3)
Top off oil tank.
Extra engine oil is used during the winteriza-
tion procedure. Some excess oil may appear
on the skeg below the gearcase area. This is
normal.
Avoid potential oil stains by placing a shop
towel or suitable container under the propel-
ler and skeg for the duration of the storage.
3)
After outboard runs for another 15 sec-
onds, press foot throttle to HALF THROT-
TLE position. Outboard will accelerate to
fast idle speed and fog itself.
43
| Categories | BRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual |
|---|---|
| Document Type | Boat Motor Manual. Marine Operator's Engine Guide. |
| Tags | Evinrude 200 hp, Evinrude 225 hp, Evinrude 250 hp, Evinrude 3.3 Liter, Evinrude 3.4 Liter, Evinrude 300 hp, Evinrude 90, Evinrude CX, Evinrude CZ, Evinrude HSL, Evinrude HVL, Evinrude HX, Evinrude PL, Evinrude PX, Evinrude PZ |
| Model Year | 2011 |
| Download File |
|
| Document File Type | |
| Publisher | evinrude.com |
| Wikipedia's Page | Evinrude Outboard Motors |
| Copyright | Attribution Non-commercial |
(2 votes, average: 2.5 out of 3)
Marine readers have rated 2011 Evinrude 200 225 250 300 hp E-TEC HSL HVL HX PL PX PZ CX CZ 3.3 3.4 Liter 90 Outboard Boat Motor Owners Manual 2.5 out of 3.0 based on 2 product reviews. not sure yet