Using Your E-TEC Outboard
OIL AND FUEL
OIL REQUIREMENTS
OILING SYSTEM
Evinrude/Johnson Brand Oils
If the “LOW OIL” warning light illuminates,
you have a limited amount of time of normal
operation before running out of oil. Refill the
oil tank with approved oil as soon as possible.
deposits, providing superior lubrication, and Always “top off” your oil tank prior to pro-
longed usage or long trips.
Evinrude/Johnson outboard oils are formulat-
ed to give best engine performance while
controlling piston and combustion chamber
ensuring maximum spark plug life.
The following outboard oils are recommend- New outboards are programmed to use addi-
ed for use in your Evinrude E-TEC outboard: tional oil during the first two hours of opera-
tion above 2000 RPM.
•
•
•
Evinrude/Johnson XD100;
Evinrude/Johnson XD50; or
Evinrude/Johnson XD30.
Refer to Engine Monitoring on page 34.
NOTICE
When operating in conditions
Evinrude/Johnson
XD100 oil must be used.
Evinrude/Johnson XD100 Oil
under
32°F
(0°C),
Evinrude/Johnson XD100 oil is preferred
for your Evinrude E-TEC outboard. This
synthetic formula oil provides uncompro-
mised lubrication and superior performance,
even in extreme conditions—especially in
cold temperatures down to 0°F (-17°C).
If requested, an authorized dealer can pro-
gram your Evinrude E-TEC outboard EMM
for the exclusive use of Evinrude/Johnson
XD100. Only an authorized Evinrude deal-
er can program your outboard for this op-
tional benefit. Oil consumption is reduced if
the outboard is programmed for exclusive
Always keep an extra supply of outboard oil in
the boat. Refer to Oil Requirements on page
16.
If you run the oil tank empty, you MUST refill
the oil tank and prime the oil system before
using the engine. Refer to Filling the Oil
Tank on page 17 and Priming the Oil Sys-
tem on page 17.
If the oil hose is disconnected for any reason,
seal it to prevent spillage. Install a cap on the
hose fitting to prevent contamination.
use of Evinrude/Johnson XD100 as com- You must use an oil tank equipped with a filter
pared to using a conventional oil. The XD100 and an oil supply hose. The oil system must
oil setting is not available on all models.
be purged if air is in the oil supply hose. Refer
to Priming the Oil System on page 17.
IMPORTANT: If your EMM has been pro-
grammed for Evinrude/Johnson XD100,
DO NOT use any other oil unless in an emer-
gency. If Evinrude/Johnson XD100 is tempo-
rarily unavailable, a one-time-only use of an
oil that meets NMMA TC-W3 certification
standards is allowed. If you discontinue using
Evinrude/Johnson XD100, you MUST first re-
turn to your Dealer to have the EMM repro-
grammed back to the original factory setting.
Other Oils
If Evinrude/Johnson brand oils are not avail-
able, you must use an oil that meets NMMA
TC-W3 certification standards.
Install the oil tank following the instructions
provided with the unit.
IMPORTANT: Failure to follow oil specifica-
tions could void the engine warranty if a lubri-
cation-related failure occurs.
16
Categories | BRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual |
---|---|
Document Type | Boat Motor Manual. Marine Operator's Engine Guide. |
Tags | Evinrude 200 hp, Evinrude 225 hp, Evinrude 250 hp, Evinrude 3.3 Liter, Evinrude 3.4 Liter, Evinrude 300 hp, Evinrude 90, Evinrude CX, Evinrude CZ, Evinrude HSL, Evinrude HVL, Evinrude HX, Evinrude PL, Evinrude PX, Evinrude PZ |
Model Year | 2011 |
Download File |
|
Document File Type | |
Publisher | evinrude.com |
Wikipedia's Page | Evinrude Outboard Motors |
Copyright | Attribution Non-commercial |
(2 votes, average: 2.5 out of 3) Marine readers have rated 2011 Evinrude 200 225 250 300 hp E-TEC HSL HVL HX PL PX PZ CX CZ 3.3 3.4 Liter 90 Outboard Boat Motor Owners Manual 2.5 out of 3.0 based on 2 product reviews.
not sure yet