Product Information
YOUR EMISSION CONTROL WARRANTY RIGHTS AND OBLIGATION
The California Air Resources Board and Bombardier Recreational Products (“BRP”) are pleased to explain the emission
control system warranty on your 2009 Evinrude E-TEC outboard. In California, new outboard engines must be designed,
built, and equipped to meet the State's stringent anti-smog standards. BRP must warrant the emission control system on
your outboard for the periods of time listed below provided there has been no abuse, neglect, or improper maintenance
of your outboard.
Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and
catalytic converter. Also included may be hoses, belts, connectors, and other emission-related assemblies.
Where a warrantable condition exists, BRP will repair your outboard at no cost to you including diagnosis, parts, and labor
provided that such work is performed by an authorized BRP dealer.
Manufacturer's Limited Warranty Coverage
This emission limited warranty covers Evinrude outboards certified and produced by BRP for sale in California, that are
originally sold in California to a California resident, or subsequently warranty-registered to a California resident. The BRP
U.S. and Canada limited warranty conditions for Evinrude outboards are still applicable to these models with the neces-
sary modifications.
Select emission control parts of your Evinrude E-TEC outboard are warranted from the date of purchase by the first retail
consumer or the date the product is first put to use, whichever occurs first, for a period of: 4 years, or for 250 hours of
use, whichever occurs first.
However, warranty coverage based on the hourly period is only permitted for outboards equipped with the appropriate
hour meters or their equivalent. If any emission-related part on your engine is defective under warranty, the part will be
repaired or replaced by BRP.
Parts covered are:
1. Electrical System
A. EMM (Engine Management Module)
B. Spark Plugs and Wires
C. Ignition Coils
4. Air Induction System
A. Reed Valves
B. Throttle Body Assembly
C. Intake Manifold
D. Wiring Harness
5. Oil System
2. Exhaust System
A. Oil Injector
A. Inner Exhaust Housing
B. Adaptor (Exhaust Manifold)
C. Megaphone (Inner Exhaust)
B. Oil Lines, Fittings, and Clamps
6. Sensors
A. Air Temperature Sensor
B. Crank Position Sensor
C. Throttle Position Sensor
D. Water Temperature Sensor
E. Thermostat
3. Fuel System
A. Fuel Lift Pump
B. Fuel Supply Pump
C. Fuel Injectors
D. Vapor Separator
E. Fuel Lines, Fittings, and Clamps
7. Gaskets
A. All Emission Component Gaskets
The emission warranty covers damage to other engine components that is caused by the failure of a warranted part.
The BRP Operator's Guide provided contains written instructions for the proper maintenance and use of your outboard.
All emission warranty parts are warranted by BRP for the entire warranty period of the outboard, unless the part is sched-
uled for replacement as required maintenance in the Operator's Guide.
Emission warranty parts that are scheduled for replacement, as required maintenance, are warranted by BRP for the pe-
riod of time before the first scheduled replacement date for that part. Emission warranty parts that are scheduled for reg-
ular inspection but not regular replacement are warranted by BRP for the entire warranty period of the outboard. Any
emission warranty part repaired or replaced under the terms of this warranty statement is warranted by BRP for the re-
mainder of the warranty period of the original part. All parts replaced under this limited warranty become the property of
BRP.
Maintenance receipts and records should be transferred to each subsequent owner of the outboard.
Owner's Warranty Responsibilities
As the outboard owner, you are responsible for the performance of the required maintenance listed in your Operator's
Guide. BRP recommends that you retain all receipts covering maintenance on your outboard, but BRP cannot deny war-
ranty solely for the lack of receipts or your failure to ensure the performance of all scheduled maintenance.
As the outboard owner, you should however be aware that BRP may deny you warranty coverage if your outboard or a
part has failed due to abuse, neglect, improper maintenance, or unapproved modifications.
You are responsible for presenting your outboard to an authorized BRP dealer as soon as a problem exists. The warranty
repairs will be completed in a reasonable amount of time, not to exceed 30 days.
For any questions regarding your warranty rights and responsibilities or for the name and location of the nearest autho-
rized BRP dealer, contact BRP US Inc. / Outboard Engines Division, After Sales Support, P.O Box 597, Sturtevant, WI
53177, 1-847-689-7090 or visit www.evinrude.com.
52
| Categories | BRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual |
|---|---|
| Tags | Evinrude 115 hp, Evinrude 130 hp, Evinrude 150 hp, Evinrude 175 hp, Evinrude 200 hp, Evinrude BX, Evinrude CX, Evinrude HL, Evinrude HX, Evinrude MX, Evinrude PL, Evinrude PX, Evinrude SL |
| Model Year | 2009 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)