2007 Evinrude 115 150 175 200 hp E-TEC PL PX SL HL CX Outboard Motor Owners Manual

   Maintenance
IMPORTANT:  Do  not  run  your  outboard—   SCRATCH REPAIR
even  for a  brief  start-up—without supplying
water to it. Refer  to Transportation on page
36.
Surface  scratches on  the  upper  and lower
Following  Starting,  Stopping,  Shifting  on    engine covers can be painted.
page 14,  start the  outboard. If  the outboard
IMPORTANT:  Your Dealer  has  the profes-
was  auto-winterized,  it  will   emit  a  puff  of
smoke on  the first start  of the season.  Let it
idle while you:
sional materials and matching paint colors to
properly repair scratches. See your Dealer to
repair any deep scratches or gouges.
Observe  running   quality.  If  poor,   refer  to
Troubleshooting  on  page  39  or see  your
Dealer.
Confirm  water pump  operation. Water  must
flow from the water pump indicator in a steady
stream. If  it does  not,  shut off  the outboard
and investigate.  Refer to  Engine Overheat-
ing on page 22.
SPARK PLUGS
WARNING
The ignition system presents a serious
shock hazard. The primary circuit oper-
ates in excess of 200 volts; the second-
ary circuit operates in excess of 25,000
volts. Use caution  to avoid injury  from
shock  or   injury  resulting   from  your
reaction  to shock.  Do  not  handle pri-
mary   or  secondary   ignition   compo-
nents  while the  engine  is cranking  or
running.
Stop the outboard and check the fuel  system
for leaks.
WARNING
Failure to check  for fuel leakage  could
allow a leak to go undetected, resulting
in fire or explosion.
IMPORTANT: The spark plugs should be ser-
viced by an Evinrude E-TEC Dealer. Incorrect
spark plug  maintenance  can lead  to engine
malfunction.
HULL FINISH
The  condition of  your  boat’s bottom  affects
performance. Marine growth or bottom  paint-
ing may reduce speed and fuel efficiency.
For maximum  performance, keep  the boat’s
running surface clean  by rinsing it with  fresh
water and wiping  it dry. Apply Evinrude   anti-
corrosion spray to any surface subject to cor-
rosion, but avoid the anti-corrosion anode(s).
SUBMERGED OUTBOARD
If your outboard has been under water,   have
it serviced  immediately upon  recovery. If
immediate   service   is   unavailable,   resub-
merge it in fresh water to avoid prolonged ex-
posure to the atmosphere.
OUTBOARD EXTERNAL FINISH
After submersion, all boat and engine electri-
cal, fuel, and oiling systems must be inspect-
ed for  signs of  water intrusion.  Your Dealer
should perform this service.
Periodically,  wash the  entire  boat and  out-
board with  soapy water and  apply a coat of
automotive wax.  Leave the  engine cover  in
place when washing the outboard.
IMPORTANT: When trailering your outboard,
DO  NOT cover  the  engine with  canvas—it
will  dull the  finish of  the  outboard’s engine
covers.
38
Product Specification
CategoriesBRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual
Tags, , , , , , , ,
Model Year2007
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 62 pages
Document File TypePDF
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website