Using Your E-TEC Outboard
Minimum Octane
WARNING
Your outboard is certified to operate on un-
leaded automotive gasoline with an octane
rating equal to or higher than:
Store fuel tanks in a well-ventilated
area, away from heat and open flame.
Prevent escape of liquid or vapors
which could accidentally ignite.
•
•
87 (R+M)/2 AKI — Inside the U.S.
90 RON — Outside the U.S.
Using unleaded gasoline that contains methyl
tertiary butyl ether (MTBE) is acceptable
ONLY if the MTBE content does not exceed
Close the filler cap vent screw, if
equipped.
15%
by volume.
Be sure the disconnected fuel hose
does not drip.
Alcohol Fuels
Your outboard has been designed to operate
using the specified fuels; however, be aware
of the following:
IMPORTANT: Fuel distribution hoses in the
boat must deliver fuel at the rate of flow need-
ed by the outboard. Minimum inside diameter
•
•
•
The boat’s fuel system may have different of fuel hoses must be 3/8 in. (9 mm).
requirements regarding the use of alcohol
Fuel systems with built-in tanks, particularly
fuels. Refer to the boat’s owner guide.
those that include antisiphon valves and filter/
primer units, may have restrictions not allow-
Alcohol attracts and holds moisture that can
cause corrosion of metallic parts in the fuel
ing the engine fuel pump to deliver sufficient
system.
fuel under all conditions. This can result in a
loss of performance. If a performance prob-
lem exists, see your Dealer.
Alcohol blended fuel may cause engine per-
formance problems.
Using alcohol-extended fuels is acceptable
ONLY if the alcohol content does not exceed:
FUEL ADDITIVES
The only fuel additives approved for use in
your Evinrude E-TEC outboard are:
•
•
10% ethanol by volume; or
5% methanol with 5% cosolvents by volume.
•
•
Use of other fuel additives can result in
poor performance or engine damage.
Evinrude/Johnson 2+4 Fuel Conditioner
Evinrude/Johnson Fuel System Cleaner
FUEL SYSTEM OPERATION
Connecting the Fuel Hose
Evinrude/Johnson 2+4 Fuel Conditioner will
help prevent gum and varnish deposits from
forming in fuel system components and will
remove moisture from the fuel system. It can
be used continuously and should be used
during any period when the outboard is not
being operated on a regular basis. Its use will
reduce spark plug fouling, fuel system icing,
and fuel system component deterioration.
1)
2)
If the fuel hose is disconnected for any rea-
son, seal it to prevent spillage. Cap the fuel
fitting to prevent contamination.
Connect the fuel hose to the 3/8 in. (9 mm)
fuel fitting. Fasten hose securely with
clamp (18.5 mm) from owner’s kit.
Evinrude/Johnson Fuel System Cleaner will
help keep fuel injectors in optimal operating
condition.
1
1.
Fuel hose – 3/8 in. (9 mm)
16
| Categories | BRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual |
|---|---|
| Tags | Evinrude 115 hp, Evinrude 150 hp, Evinrude 175 hp, Evinrude 200 hp, Evinrude BX, Evinrude CX, Evinrude HL, Evinrude PL, Evinrude PX, Evinrude SL |
| Model Year | 2008 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Marine readers have rated 2008 Evinrude 115 150 175 200 hp E-TEC PL PX SL BX HL CX Outboard Motor Owners Manual 5.0 out of 5.0 based on 1 product reviews. I own a 2008 Etec and would like to review the manual.