X OIL AND FUEL
Minimum Octane
WARNING
Your outboard is certified to operate on un-
leaded automotive gasoline with an octane
rating equal to or higher than:
Store fuel tanks in a well-ventilated
area, away from heat and open flame.
Prevent escape of liquid or vapors
which could accidentally ignite.
•
•
87 (R+M)/2 AKI — Inside the U.S.
90 RON — Outside the U.S.
Using unleaded gasoline that contains methyl
tertiary butyl ether (MTBE) is acceptable
ONLY if the MTBE content does not exceed
Close the filler cap vent screw, if
equipped.
15%
by volume.
Be sure the disconnected fuel hose
does not drip.
Alcohol Fuels
Your outboard has been designed to operate
using the specified fuels; however, be aware
of the following:
IMPORTANT: Fuel distribution hoses in the
boat must deliver fuel at the rate of flow need-
ed by the outboard. Minimum inside diameter
•
•
•
The boat’s fuel system may have different of fuel hoses must be 3/8 in. (9 mm).
requirements regarding the use of alcohol
fuels. Refer to the boat’s owner guide.
WARNING
Alcohol attracts and holds moisture that can
cause corrosion of metallic parts in the fuel
The
outboard
must
be
correctly
system.
installed. Failure to correctly install the
outboard could result in property dam-
Alcohol blended fuel may cause engine per-
formance problems.
age,
serious injury, or death. We
strongly recommend your Dealer install
your outboard to ensure proper instal-
lation.
Using alcohol-extended fuels is acceptable
ONLY if the alcohol content does not exceed:
•
•
10% ethanol by volume; or
5% methanol with 5% cosolvents by vol-
ume.
Fuel systems with built-in tanks, particularly
those that include antisiphon valves and filter/
primer units, may have restrictions not allow-
ing the engine fuel pump to deliver sufficient
fuel under all conditions. This can result in a
loss of performance. If a performance prob-
lem exists, see your Dealer.
FUEL SYSTEM OPERATION
Connecting the Fuel Hose
1)
If the fuel hose is disconnected for any rea-
son, seal it to prevent spillage. Cap the fuel
fitting to prevent contamination.
2)
Connect the fuel hose to the 3/8 in. (9 mm) FUEL ADDITIVES
fuel fitting. Fasten hose securely with
BRP approves only Evinrude 2+4® fuel con-
clamp (18.5 mm) from owner’s kit.
ditioner fuel additive for use in your Evinrude
E-TEC outboard.
Use of other fuel additives can result in poor
performance or engine damage.
Evinrude 2+4 fuel conditioner will help pre-
vent gum and varnish deposits from forming
in fuel system components and will remove
moisture from the fuel system.
1
It should be used during any period when your
engine is not being operated on a regular ba-
sis. Its use will reduce fuel system icing and
fuel deterioration.
1.
Fuel hose and fitting – 3/8 in. (9 mm)
19
| Categories | Evinrude E-TEC Manual, Evinrude Outboard Manual |
|---|---|
| Tags | Evinrude 40 hp, Evinrude 50 hp, Evinrude 60 hp, Evinrude EL, Evinrude PL |
| Model Year | 2006 |
| Download File |
|
| Document File Type | |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Marine readers have rated 2006 Evinrude 40 50 60 hp E-TEC EL PL Outboard Owners Manual 5.0 out of 5.0 based on 1 product reviews. I really appreciate having access to this information it’s seems really accurate and informative thank you very much