Blistering refers to a condition in which the unprotected use chlorine or ammonia products. These products can
gel coat surface below the waterline has absorbed wa- affect the color of gel coat. Commercial car washes use
ter and formed bubbles. See Section O-5 for additional strong cleaners and should be avoided.
information.
To remove stains, refer to the procedures below.
Follow the instructions below for boats that have weath-
ered and chalked.
1.
2.
Wash area with hand dishwashing soap.
1.
2.
Wash.
Begin with a small area such as three feet by three
feet and apply a mild cleanser.
Wax. If this does not work, then use a fine rubbing
compound. If this does not work use 400 or 600 wet
ordrysandpaper,followedbyfinerubbingcompound
and wax.
3.
4.
Rinse with clean water.
Follow with compound and waxing as outlined in
procedure above.
When using wax or fine rubbing compounds, make sure
to read the label and follow the directions. Some helpful If the stain is not removed by the hand dishwashing soap
tips are listed below.
or mild cleanser, then the next procedure is to use either
denatured or rubbing alcohol. If this does not work, con-
1.
2.
Avoid working in direct sunlight. This dries out the sult your Four Winns dealer for professional assistance.
wax or compound, and can stain the surface.
NOTICE
Use clean pads or cloths to apply a thin coating of
wax or rubbing compound to a small area such as
three feet by three feet. Remove any excess, and
then rub the area with a buffing pad, or power buffer.
Apply pressure only as necessary to restore the sur-
DO NOT use acetone, ketone, or other solvents
to remove stains. These chemicals are flam-
mable and may damage the gel coat.
face finish. Applying too much pressure or buffing O - 5 FIBERGLASS REPAIRS
in one place too long can permanently damage the
surface.
Fiberglass is one of the most durable, strong, and for-
giving construction materials afloat. It is resilient and
After applying compound, always follow with wax- normalrepairscanbemadewithoutaffectingthestrength
3.
ing.
or structural integrity of the boat.
NOTICE
If using a power buffer, use a low RPM buffer
with light pressure. Keep the pad wet and the
buffer moving at all times to prevent heat build
up.
Striking docks, other boats, or submerged ob-
jects could create a very hazardous situation or
severely damage the fiberglass. In the event
an object is struck below or near the waterline,
proceed directly and cautiously to the nearest
service facility and remove the boat from the
water. Closely inspect the hull for damage. If
the outer fiberglass laminate was penetrated,
repairs must be made prior to relaunch.
NOTICE
To preventgouges,unevenareas,orotherdam-
age from occurring, DO NOT use a power or
belt sander when sanding. For best results,
block sand the gel coat.
Occasionally, blisters, crazing, scratches, or damage to
the fiberglass can occur. Repairs may be necessary to
correct the problem.
C. Stains
Stains can appear anywhere on the exterior of the boat
and may be a result of contact with tar, plant sap, leaves,
rust from metal fittings, and other materials. Surface
stains may be removed with hand dishwashing soap,
mild cleansers, or some household detergents. DO NOT
1
Owner’s Manual
08/01
80/190/200 Horizon
Section O
Page 3
| Categories | Four Winns Manuals, Outboard Marine Corporation Manuals |
|---|---|
| Model Year | 2001, 2002, 2003 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx |
| Document File Type | |
| Publisher | fourwinns.com |
| Wikipedia's Page | Outboard Marine Corporation |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Marine readers have rated 2001-2003 Four Winns Horizon 180 190 200 Owners Manual 5.0 out of 5.0 based on 1 product reviews. Had a hard time opening the file.
Some do open