NOTICE
The positive and negative studs incorporated
into the battery switch panel are intended to
raise the engine hatch when properly attached
to an external 12 volt source (12 volt battery).
Once properly attached to the 12 volt source
use the engine hatch switch at the helm to
raise the engine hatch. These studs are not
designed for jump-starting a dead battery.
To prevent electrical problems, use only
replacement fuses or breakers that are of
equal rating to the originals.
Accessories - Additional 12 volt equipment may be
added to the boat by the using the accessory switch-
es. Depending on the model, certain accessories may
be wired directly to the fuse block below the dash or
may be wired to a circuit breaker in the AC/DC cabin
panel. For additional information on adding accesso-
ries, refer to Section H-5B.
H - 3 BATTERY CHARGER
The battery charger is standard on the V355 models
and is located in engine compartment. The batteries
will be charged by the battery charger when the boat
is connected to dockside power and the AC circuit
breakers and BATTERY CHARGER circuit breaker
are “ON”. If a generator is available and operating, it
too will allow the batteries to be charged by the battery
charger.
12
12
appropriate adaptor, the equipment draws power from
the boat’s batteries.
Volt DC Receptacle - Permits the use of additional
volt equipment such as a cell phone. Using the
Aft Bilge Pump - The BILGE PUMP switch is used
to manually activate the bilge pump in the engine
compartment. The bilge pump is used to remove
water from the bilge (bottom of the hull) area of the
boat by pumping that water overboard. The aft bilge
pump is equipped with an automatic bilge switch and
will operate whenever bilge water rises to a level that
will cause the float to move upward.
Additional information on the battery charger can be
found in Section H-8B - 120 Volt AC Equipment in this
manual and refer to the manufacturer’s literature
included with the owner’s packet.
H - 4 VOLTMETER
This automatic bilge pump is active even if the battery
selector switch is in the “OFF” position. The auto matic
bilge pump circuitry is connected directly to the
batteries. When leaving your boat unattended for an
ex tend ed period, check the charge on the battery(s)
periodically. Also check the water level in the bilge
and make sure the float switch is functional.
Dual gauges with voltmeters are installed in the dash
panel to monitor the condition of the engine battery(s).
When the voltage is checked during engine operation,
the voltage of the respective battery will be indicated
on the respective voltmeter. It should be noted that
located on the 12V DC system side of the AC/DC
cabin panel is a voltmeter which monitors the “SHIPS
SYSTEMS” battery. Additional informa tion on voltme-
ters may be found in the engine owner’s manual.
If the automatic bilge pump must be disabled, discon-
nect the wiring plug near the bilge pump.
Blower - The BLOWER switch is used to activate the
bilge blower. Pressing the switch to the “ON” position,
activates the electric bilge blowers, changing the air in
the engine compartment that may contain gas vapors.
H - 5 12 VOLT ELECTRICAL EQUIPMENT
A. Helm Equipment
Ignitions are protected by circuit breakers on the V355
model. Equipment on the helm is protected by either
circuit breakers in the helm or in the cabin’s AC/DC
panel.
To assist you, we have listed the descriptions of
individual switches, receptacles and their uses:
Electrical Systems - Section H
Owner’s Manual Page 71
| Categories | Four Winns Manuals, Four Winns V-Series Manuals |
|---|---|
| Tags | Four Winns V355 |
| Model Year | 2011 |
| Download File |
|
| Document Type | Owner's Manual |
| Language | English |
| Product Brand | Boats and Cruisers, Four Winns. For support contact your dealer at http://www.fourwinns.com/locate-dealer.aspx |
| Document File Type | |
| Publisher | fourwinns.com |
| Wikipedia's Page | Outboard Marine Corporation |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)