2005 Yamaha Outboard VX200D Boat Motor Owners Manual

Maintenance
parts while the engine is running.
5
3
q
2-hp   models:   The   propeller   rotates
whenever the engine is running. Do not
move the throttle control lever from the
start position during warm-up. The boat
4
could
which could result in an accident.
unexpectedly   start   to   move,
2
1
ECM00490
CAUTION:
ZMU03560
This procedure must be performed  while
the  outboard  motor  is  in  the  water.  A
flushing attachment  or  test tank  can be
used.
1
2
3
4.
5.
. Filter cup ring nut
. Filter cup
. Filter element
O-ring
Filter housing
A diagnostic tachometer should  be used for
this procedure. Results may vary depending
4.
Reinstall  the filter  element  in  the cup.     on  whether  testing  is  conducted  with  the
Make sure the O-ring is in position in the    flushing attachment, in a test tank, or with the
cup. Insert the cup and O-ring into the fil-   outboard motor in the water.
ter housing. Lift up and  hold the locking
tab to  screw the  ring nut onto  the filter
housing until the ring is lightly seated.
Tighten  the  ring nut  approximately  an
additional  1/4 turn  until  the ring  nut  is
tight. Align one of the four larger ring nut
tabs with the locking tab and release it to
lock the ring nut in position.
1.
Start the engine and allow it to warm up
fully in neutral until it is running smooth-
ly.
2-hp model:  Warm the  engine with  the
throttle in the start position or less. If the
outboard is mounted on a boat, be  sure
the boat is tightly moored.
5.
6.
NOTE:
Run the engine and check  the filter and    Correct idling speed inspection is only possi-
lines for leaks.
NOTE:
ble if  the  engine is  fully warmed  up. If  not
warmed up fully, the idle speed will measure
If any water is in  the fuel, the red ring in the     higher than normal. If you have difficulty ver-
fuel filter unit will float. If so, remove the cup     ifying the  idle  speed, or  the idle  speed re-
and drain the water.
quires adjustment, consult a Yamaha dealer
or other qualified mechanic.
EMU29040
Inspecting idling speed
2.
Verify whether  the idle  speed  is set  to
specification.  For idle  speed  specifica-
tions, see page 39.
EWM00450
WARNING
q
q
Do not touch or remove electrical parts
when starting or during operation.
Keep  hands,  hair,   and  clothes  away
EMU29050
Checking water in engine oil tank
Oil injection models
from  the  flywheel  and  other  rotating     There is a water trap at the bottom of the en-
50
Product Specification
CategoriesYamaha Outboard Manuals
Document TypeBoat Motor Manual Free Download. Marine Operator's Boating Guide.
Tags
Model Year2005
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 81 pages
LanguageEnglish
Product BrandYamaha Motor. Yamaha Motor Corporation, USA - Support Customer Relations for US: 1-800-962-7926
Yamaha Boats: 1-800-962-7926
Yamaha Outboard Customer Relations: 1-866-894-1626 , Yamaha Outboard
Document File TypePDF
Publisheryamaha-motor.com
Wikipedia's PageYamaha Motor Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website