2011 Evinrude 200 225 250 300 hp E-TEC HSL HVL HX PL PX PZ CX CZ 3.3 3.4 Liter 90 Outboard Boat Motor Owners Manual

   Product Information
INSTALLATION AND ACCESSORIES
TRANSOM HEIGHT
Make sure  the  transom height  matches  the
length of the outboard to be installed.
WARNING
Your outboard must not exceed the
maximum  horsepower indicated  on     •  A 19  to  21 in.  (48.3 to  53.3  cm) transom
the boat’s capacity plate. Such over-
powering can cause loss of control.
Contact  your  Dealer  or  the   boat’s
manufacturer  if  your  boat  lacks  a
capacity plate.
height  uses a  20  in. (50.8  cm)  shaft out-
board.
The shaft  length of  the outboard  being in-
stalled should  come close to  matching the
transom height of the boat.
Determine transom height by measuring from
the top edge of the transom, along the center-
line.
Boats  designed  for  remote-steered
outboards might be overpowered by
a tiller-steered outboard of the maxi-
mum  rated  horsepower.   Ask  your
Dealer  or  boat  manufacturer  if  you
are  unsure  about  your  boat’s  suit-
ability.
Incorrectly  matched  boat  and  out-
board  transom  heights   can  cause
boat instability and loss of control.
Refer to Transom Height.
1
3
2
Prevent lateral movement   and pos-
sible  outboard   loss  by  using   the
mounting    hardware    supplied   or
1.  Centerline
2.
3.
Antiventilation plate
Transom Height
hardware
of
sufficient
size,
strength, and quality. Refer to Install-
ing the Outboard on page 49.
Boat   performance   depends   on   outboard
mounting height.
A mounting surface that is damaged
or too thin to support your outboard     Generally,   the  anti-ventilation  plate   of  the
gearcase should align  with the bottom of the
while  underway   might   fail  during
hull. Conventional  V-hulls often perform  well
operation, causing a loss of control.
with the anti-ventilation plate approximately 1
Be   sure   the    boat’s   transom   or
in. (25 mm) above the bottom of the hull.
mounting   bracket    is   structurally
Test outboard and boat performance at differ-
sound and between 1 5/8 in. (41 mm)
ent  heights   until  the  best   performance  is
and 2 3/4 in. (70 mm) in thickness.
achieved.
IMPORTANT:  Be sure  that  outboard  water
NOTICE
Use an appropriate hoist to lift   pressure  is   not  adversely  affected  by   the
the  engine.   Refer  to   Specifications  on    mounting height of the outboard.
page 53 for engine weight.
48
Product Specification
CategoriesBRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual
Document TypeBoat Motor Manual. Marine Operator's Engine Guide.
Tags, , , , , , , , , , , , , ,
Model Year2011
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 76 pages
Document File TypePDF
Publisherevinrude.com
Wikipedia's PageEvinrude Outboard Motors
CopyrightAttribution Non-commercial
(2 votes, average: 2.5 out of 3)
Marine readers have rated 2011 Evinrude 200 225 250 300 hp E-TEC HSL HVL HX PL PX PZ CX CZ 3.3 3.4 Liter 90 Outboard Boat Motor Owners Manual 2.5 out of 3.0 based on 2 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

2011 Evinrude 200 225 250 300 hp E-TEC HSL HVL HX PL PX PZ CX CZ 3.3 3.4 Liter 90 Outboard Boat Motor Owners Manual SKU UPC Model
jay on Jun 02, 2014. don't know

not sure yet


tim plude on Sep 15, 2013.



Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website