2004 Evinrude 75 90 hp E-TEC PL PX SL Outboard Motor Owners Manual

OIL AND FUEL
Minimum Octane
WARNING
Your outboard  is certified  to operate  on un-
leaded  automotive gasoline  with  an  octane
rating equal to or higher than:
Store  fuel   tanks  in   a  well-ventilated
area, away  from heat  and open  flame.
Prevent   escape  of   liquid   or  vapors
which could accidentally ignite.
87 (R+M)/2 AKI — Inside the U.S.
90 RON — Outside the U.S.
Using unleaded gasoline that contains methyl
tertiary  butyl   ether   (MTBE)  is   acceptable
ONLY if the  MTBE content does  not exceed
Close   the   filler   cap  vent   screw,   if
equipped.
15%
by volume.
Be  sure  the   disconnected  fuel  hose
does not drip.
Alcohol Fuels
Your outboard has been designed to operate
using the specified fuels;  however, be aware
of the following:
IMPORTANT: Fuel  distribution hoses  in the
boat must deliver fuel at the rate of flow need-
ed by the outboard. Minimum inside diameter
The boat’s  fuel system may  have different    of fuel hoses must be 3/8 in. (9 mm).
requirements regarding  the use  of alcohol
fuels. Refer to the boat’s owner guide.
WARNING
Alcohol attracts and holds moisture that can
cause corrosion of metallic parts in  the fuel
The
outboard
must
be
correctly
system.
installed. Failure to correctly  install the
outboard could result  in property dam-
Alcohol blended fuel may cause engine per-
formance problems.
age,
serious   injury,    or   death.    We
Using  alcohol-extended  fuels  is  acceptable
ONLY if the alcohol content does not exceed:
strongly recommend your Dealer install
your outboard  to ensure proper  instal-
lation.
10% ethanol by volume; or
5%  methanol with  5%  cosolvents  by  vol-
ume.
Fuel systems  with  built-in tanks,  particularly
those that include antisiphon valves and filter/
primer units, may have restrictions not  allow-
ing the engine  fuel pump to deliver  sufficient
fuel under all  conditions. This can result  in a
loss of  performance. If  a performance  prob-
lem exists, see your Dealer.
FUEL SYSTEM OPERATION
Connecting the Fuel Hose
1)
If the fuel hose is disconnected for any rea-
son, seal it to prevent spillage. Cap the fuel
fitting to prevent contamination.
2)
Connect the fuel hose to the 3/8 in. (9 mm)  FUEL ADDITIVES
fuel   fitting.  Fasten   hose   securely  with
Bombardier  approves  only   Evinrude  2+4®
clamp (18.5 mm) from owner’s kit.
fuel conditioner  fuel additive  for use  in your
Evinrude E-TEC outboard.
Use of other  fuel additives can result in  poor
performance or engine damage.
Evinrude 2+4 fuel conditioner will help pre-
vent gum  and varnish deposits from  forming
in fuel  system  components and  will remove
moisture from the fuel system.
It should be used during any period when your
engine is not being operated on a regular ba-
sis. Its  use will reduce fuel  system icing and
fuel deterioration.
1.
Fuel hose and fitting – 3/8 in. (9 mm)
17
Product Specification
CategoriesBRP Brand Manuals, Evinrude Brand Manuals, Evinrude E-TEC Manual, Evinrude Outboard Manual
Tags, , , ,
Model Year2004
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 60 pages
Document File TypePDF
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website